Blacktop 20 valve parts

lotusnutt · 09-24-2007, 12:50 PM

Looking for: Blacktop engine wiring harness complete, MAP sensor
and ECU. (yeh, I know so is everyone else)

TOP $$$ paid

I have some silvertop parts for trade.

whatcha' got??

bob

transamdrifter · 01-03-2008, 12:28 PM

call Black Ops 321 402 6622 they are in Cocoa Fl.

mr220v · 01-03-2008, 01:45 PM

If you can't find one, It may be possible to make my standard mr2 blacktop harness work in a kit car. I'd use an 87 mr2 harness for the base, so that would give you enough length to mount the ecu behind the firewall. The circuit opening relay/fuelpump control is located on the mr2 engine harness, so this is covered. Main thing would be 12v for the ecu, injectors, ignition, etc.... and a 12v starter relay signal for the starter solenoid. The kit car you're working with might give you some of this.

lotusnutt · 01-04-2008, 02:55 PM

hi ya

would it be possible to use the silver top harness that I currently have?
I did find a 12 pin connector to use, I haven't had the time to work on it
like I planned. i have the AFM and silver top ECU and I don't want to put any
more $$ for black top parts into the swap at this point.

if you could do a harness like you described using these, i'd consider
this.

thanks
bob

mr220v · 01-04-2008, 03:17 PM

At this point, I could make a 20v harness without even being supplied any kind of 20v harness. A butchered silvertop harness will work perfectly well.

So, you would supply the silvertop harness, I would supply the 87 mr2 harness (I have lots of these lying around right now) with flying leads so that you could hook up your gauges, fuel pump, and 12v for the ecu.

I'm guessing you're going to run the silvertop ecu, but I can wire for either.

I'm PMing you my order form.

AW111 MR2 · 01-05-2008, 02:10 PM

mr220v knows his stuff, and provide many of us MkI owners a quality product!! He comes highly recommended!

09-24-2007, 12:50 PM	#1 (permalink)
lotusnutt No Skills Join Date: Aug 2007 Location: st.paul, MN Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	Blacktop 20 valve parts Looking for: Blacktop engine wiring harness complete, MAP sensor and ECU. (yeh, I know so is everyone else) TOP $$$ paid I have some silvertop parts for trade. whatcha' got?? bob

01-04-2008, 02:55 PM	#4 (permalink)
lotusnutt No Skills Join Date: Aug 2007 Location: st.paul, MN Posts: 10 Thanks: 6 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	silver wiring harness hi ya would it be possible to use the silver top harness that I currently have? I did find a 12 pin connector to use, I haven't had the time to work on it like I planned. i have the AFM and silver top ECU and I don't want to put any more $$ for black top parts into the swap at this point. if you could do a harness like you described using these, i'd consider this. thanks bob

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

LinkBacks (?) LinkBack to this Thread: http://www.mr2.com/forums/20v-swaps/Toyota-MR2-21377-blacktop-20-valve-parts.html
Posted By	For	Type	Date
Toyota MR2 Message Board	This thread	Refback	09-24-2007 01:24 PM

01-03-2008, 12:28 PM	#2 (permalink)
transamdrifter Some Skills Join Date: Dec 2007 Posts: 59 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	call Black Ops 321 402 6622 they are in Cocoa Fl.

01-03-2008, 01:45 PM	#3 (permalink)
mr220v Beams Owners Group Join Date: Mar 2006 Posts: 1,791 Thanks: 13 Thanked 139 Times in 117 Posts iTrader Rating: (9/100% )	If you can't find one, It may be possible to make my standard mr2 blacktop harness work in a kit car. I'd use an 87 mr2 harness for the base, so that would give you enough length to mount the ecu behind the firewall. The circuit opening relay/fuelpump control is located on the mr2 engine harness, so this is covered. Main thing would be 12v for the ecu, injectors, ignition, etc.... and a 12v starter relay signal for the starter solenoid. The kit car you're working with might give you some of this.

01-04-2008, 03:17 PM	#5 (permalink)
mr220v Beams Owners Group Join Date: Mar 2006 Posts: 1,791 Thanks: 13 Thanked 139 Times in 117 Posts iTrader Rating: (9/100% )	At this point, I could make a 20v harness without even being supplied any kind of 20v harness. A butchered silvertop harness will work perfectly well. So, you would supply the silvertop harness, I would supply the 87 mr2 harness (I have lots of these lying around right now) with flying leads so that you could hook up your gauges, fuel pump, and 12v for the ecu. I'm guessing you're going to run the silvertop ecu, but I can wire for either. I'm PMing you my order form.

01-05-2008, 02:10 PM	#6 (permalink)
AW111 MR2 No Skills Join Date: Mar 2007 Posts: 12 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	mr220v knows his stuff, and provide many of us MkI owners a quality product!! He comes highly recommended!