[canadam]

MR2Board Name - Phoenix
Real Name - David Duryea
Location - Tachikawa, Japan

Member Garage - http://www.mr2board.com/forums/vbpic...p?do=view&g=79
Website- www.phoenix-mr2.com

Modlist -
Engine
Nitrous Works 50 Shot Wet Kit
SSautoChrome Headers
Cold Air Intake
Polished Valve cover, Throttle Body, Intake Manifold
Ko Racing Quad Tipped Dual Exhaust
Suspension, wheels & tires
Cam 17" Wheels
Kyb AGX Adjustable Struts
Kumho Ecsta 215/40/R17
Interior
Fiberglassed Dash
Lilliput 7" touchscreen
Recovered Seats
XS Steering Wheel w/ Momo Hub
Toshiba Laptop w/ GPS Navigation
Exterior
Molded Body Kit
Bomex Front end
Veilside Side Skirts
Veilside Rear Bumper
TRD Widebody Wing
Toms Scoop

http://tinypic.com/k15nh1.jpg

http://tinypic.com/k15pap.jpg

turbonatormr2
Martin



MY MOD LIST
300 WHP on 91 octane and 9 pounds of boost
344 WHP on 91 octane and 14 pounds of boost.
380 WHP on 91 octane and 17 pounds of boost
9000 RPM'S

MOTOR- 3SGTE
Every single gasket was replaced.
Full street port (Block ported)
Magnaflux, bore and oil gully mod block
Micro polish, Straighten, Chamfer and balance crank
Clevite 77 bearings std
Forged Pauter Rods
Cp pistons forged
Ported Oem oil pump
Ported cylinder head
34.5 mm ferrea intake valves
30 mm ferrea exhaust valves
65 lb valve springs with titanium retainers
MRS shim-less buckets
Custom intake manifold
Arp head studs
Arp fasteners
Hks 272 intake cam
Hks 264 exhaust cam
Cold start injector eliminated
Aem cam gears
TTE metal head gasket
Egr block off plates (ko racing)
Apex blow off valve

Fuel
Wolfkatz fuel rail (bored at 9mm)
Adjustable fuel pressure regulator (Paxon)
850cc blitz fuel injectors
Toyota supra fuel pump in gas tank

Intake
Custom 4-inch intake (turbohoses)

Ignition
Ngk spark plug wires (rctx69)
Rotor and cap (Stock)
Indurium spark plugs (gap 0.28)

Intercooler
Greedy with 7.5 fan and fan shroud (fan shroud made by Hux-Racing)
TRD thermostat high performance low temp.

Transmission
Lsd
Light weight Fidanza fly wheel
Spec clutch with upgraded pressure plate

Turbo
Garrett Hybird GT30 dual ball bearing turbo center section TS04(T58) compressor housing, T3 (.82 a/r) exhaust turbine housing with 3inch round outlet. Custom 3 inch down pipe with a tail 40mm waste gate with .9 bar spring Waste gate down pipe that dumps to air.

Exhaust
Tko dual exhaust (Ko-Racing) 2.5

EMS
Nemesis (Installed and tuned by Ricky-B)
Tuned on 91 Octane and 14 pounds of boost
Tuned on 91 octane and 17 pounds of boost

Electronics
Apex boost controller
Greddy turbo timer

Rims and tires (Nexen N-3000 ZR) High performance
Front 215/40/17x7.5
Rear 235/40/17x7.5

Miscellaneous
Valve cover allen bolts
Chrome TRD oil cap
Engine anti torque bar
Motor mount inserts (kirkasourus)
Cusco tower brace (front and rear)
Auto meter boost gauge and pod
Auto meter Air/Fuel gauge and pod
White indaglow gauges
Chrome Bazel around gauge cluster
Heat wraps for down pipe and dump tube
Short shifter (OBX)
Custom Steel braided water, and oil lines.
Optimus battery
Adjustable RPM shift light

Pictures of my car and motor.

http://img470.imageshack.us/img470/2...ures0018ls.jpg
http://img470.imageshack.us/img470/6...ures0128qb.jpg
Some motor pics
http://img470.imageshack.us/img470/6...ures0081pp.jpg
http://img470.imageshack.us/img470/2...ures0020av.jpg
http://img470.imageshack.us/img470/6...ures0209ea.jpg
http://img470.imageshack.us/img470/9...ures0327jj.jpg