no rpm

red-top · 01-28-2008, 03:32 PM

hello
my problem : I have no rpm on my cluster 91.
please help me
thanks

mr2mkii · 01-28-2008, 09:28 PM

Quote:

Originally Posted by red-top

hello
my problem : I have no rpm on my cluster 91.
please help me
thanks

you need to buy a tach adaptor from msd to make your original rpm work with the beams engine, signal isn't compatible

MSD ignition part number PN 8920 if I remember right

http://www.turbomr2.com/MR2/HowTo/En...ch_Adapter.jpg

pasqual · 02-02-2008, 01:59 AM

I had same problem

resolution:SGI-8 D

eBay Motors: DAKOTA DIGITAL TACH ADAPTER 1JZGTE 2JZGTE 4AGZE SGI-8 (item 370001393870 end time Feb-28-08 18:32:26 PST)

fosingwo · 05-26-2008, 01:12 PM

just wondering how hard is it to fit beams cluster into a 92mr2

puretone · 05-26-2008, 03:08 PM

Quote:

Originally Posted by fosingwo

just wondering how hard is it to fit beams cluster into a 92mr2

wasnt very hard to do in a 1992 celica....i dont think its any harder in a mr2
Pictars! :: Celica Show Off, southern most tip of Aruba :: PICT2597

puretone · 05-26-2008, 03:09 PM

Quote:

Originally Posted by pasqual

I had same problem

resolution:SGI-8 D

eBay Motors: DAKOTA DIGITAL TACH ADAPTER 1JZGTE 2JZGTE 4AGZE SGI-8 (item 370001393870 end time Feb-28-08 18:32:26 PST)

can you show me how you did your wiring for that particular device?

pasqual · 05-26-2008, 04:22 PM

Quote:

Originally Posted by puretone

can you show me how you did your wiring for that particular device?

there is manual

http://www.dakotadigital.com/pdf/sgi-8d.pdf

PWR - connect to +5V from ecu
GND - ground from ECU
SigIn - silver C-27 TACO from ECU
OUT1 or OUT2 I dont remember now - should go to tachometer....
try both ..one should working

You can simply cut silver cable C-27 TACO --> tachometer
and put there device :

Ecu -C27 --> SigIn [__] OUT1/2 ---> tachometer

Im far away from my car ...so Im not able checking now

01-28-2008, 03:32 PM	#1 (permalink)
red-top Beams Owners Group Join Date: May 2006 Posts: 45 Thanks: 5 Thanked 1 Time in 1 Post iTrader Rating: (0/0% )	no rpm hello my problem : I have no rpm on my cluster 91. please help me thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-02-2008, 01:59 AM	#3 (permalink)
pasqual Beams Owners Group Join Date: Apr 2007 Location: BRNO/CZ Posts: 152 Thanks: 5 Thanked 10 Times in 9 Posts iTrader Rating: (2/100% )	I had same problem resolution:SGI-8 D eBay Motors: DAKOTA DIGITAL TACH ADAPTER 1JZGTE 2JZGTE 4AGZE SGI-8 (item 370001393870 end time Feb-28-08 18:32:26 PST)

05-26-2008, 01:12 PM	#4 (permalink)
fosingwo Beams Owners Group Join Date: Feb 2007 Location: new jersey Posts: 84 Thanks: 5 Thanked 1 Time in 1 Post iTrader Rating: (1/100% )	just wondering how hard is it to fit beams cluster into a 92mr2