Creating Beams Red-Top model for Engine Analyzer Pro need help

pasqual · 08-04-2008, 01:48 AM

For create Beams Red-Top model for Engine Analyzer I need collect some details about engine :

some data missing :

Short Block:

Bore : 86mm , 3.38inch
Stroke: 86mm , 3.38inch
4 Cylin
Piston Rings: 3 lower Tension ????
Rod Lenght : 138mm , 5,433inch
Piston skirt : ?????????
Bearing Size: ????
Piston Top : Coating No???
Cyl Leakage: Low or High/typical/zero ???

Head Spec:

INTAKE

Valves/port: 2/1
IN valve diameter: 34,5mm
IN avg port diameter: 40/49mm ??? is about 45mm diameter ???
Port Lenght: ????
Flow Coefficient: ??? single or Flow tabe (valve lift/CFM)

Compression Ratio : 11:1

EXHAUST
Valves/port: 2/1
EX valve diameter: 29.5mm
EX avg port diameter: ??????
Port Lenght: ????
Flow Coefficient: ???single or Flow tabe (valve lift/CFM)

Intake system:

BIG THX

Runner dia@Head: 45mm
Runer Lenght: 230mm
Runner Flow Coef: ??? (hondy Type-R mainfold have 1.5) ???

Throttle Body:
Total CFM rating calculated for 67mm diameter --> 569

Plenum Spec :
Plenum Volume: ?????
Effective Throttle Body Lenght ????
Total Throttle Body Area ????

Fuesl Delivery Specs:
injectors 340cc
Injector Rated Pres PSI 40 ???
Operating fuel Pres PSI 40 ???

Exhaust Header:
inside diameter ???
lenght ???

pasqual · 08-04-2008, 01:59 AM

CAm/valve spec:

Intake cam:

centerline , deg ATDC:???
duration @0.5" : 257 ????
Open @0.5"BTDC:???
Close @0.5"ABDC :???
Max lobe lift :????
Actial Valve Lash: ????
Designed Valve Lash: ????
Rocker ARm Ratio: 1.0
Gross Valve Lift: ?????
Dewell Over Nose
Duration @0.2": ?????

O need same for Exhaust cam
??????????????????

LObe separation:???

VAlve train dynamics (if possible get info)

Eff Valve mass:???
Eff lifter stiffness (lb/in): ????
spring rate (lb/in) ????
seated spring force (lbs):???

same for Exhaust ....

Servin · 08-08-2008, 12:51 PM

Wow lots of specifics you need there. Sadly i cant tell you anything but have you tried asking Mandalay. He has a translated service manual perhaps he can look up some values for you. I noticed Glen (Celica RA45) looked at this thread i would've figured he could help you on some of this...

08-04-2008, 01:48 AM	#1 (permalink)
pasqual Beams Owners Group Join Date: Apr 2007 Location: BRNO/CZ Posts: 152 Thanks: 5 Thanked 10 Times in 9 Posts iTrader Rating: (2/100% )	Creating Beams Red-Top model for Engine Analyzer Pro need help For create Beams Red-Top model for Engine Analyzer I need collect some details about engine : some data missing : Short Block: Bore : 86mm , 3.38inch Stroke: 86mm , 3.38inch 4 Cylin Piston Rings: 3 lower Tension ???? Rod Lenght : 138mm , 5,433inch Piston skirt : ????????? Bearing Size: ???? Piston Top : Coating No??? Cyl Leakage: Low or High/typical/zero ??? Head Spec: INTAKE Valves/port: 2/1 IN valve diameter: 34,5mm IN avg port diameter: 40/49mm ??? is about 45mm diameter ??? Port Lenght: ???? Flow Coefficient: ??? single or Flow tabe (valve lift/CFM) Compression Ratio : 11:1 EXHAUST Valves/port: 2/1 EX valve diameter: 29.5mm EX avg port diameter: ?????? Port Lenght: ???? Flow Coefficient: ???single or Flow tabe (valve lift/CFM) Intake system: BIG THX Runner dia@Head: 45mm Runer Lenght: 230mm Runner Flow Coef: ??? (hondy Type-R mainfold have 1.5) ??? Throttle Body: Total CFM rating calculated for 67mm diameter --> 569 Plenum Spec : Plenum Volume: ????? Effective Throttle Body Lenght ???? Total Throttle Body Area ???? Fuesl Delivery Specs: injectors 340cc Injector Rated Pres PSI 40 ??? Operating fuel Pres PSI 40 ??? Exhaust Header: inside diameter ??? lenght ???

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-04-2008, 01:59 AM	#2 (permalink)
pasqual Beams Owners Group Join Date: Apr 2007 Location: BRNO/CZ Posts: 152 Thanks: 5 Thanked 10 Times in 9 Posts iTrader Rating: (2/100% )	CAm/valve spec: Intake cam: centerline , deg ATDC:??? duration @0.5" : 257 ???? Open @0.5"BTDC:??? Close @0.5"ABDC :??? Max lobe lift :???? Actial Valve Lash: ???? Designed Valve Lash: ???? Rocker ARm Ratio: 1.0 Gross Valve Lift: ????? Dewell Over Nose Duration @0.2": ????? O need same for Exhaust cam ?????????????????? LObe separation:??? VAlve train dynamics (if possible get info) Eff Valve mass:??? Eff lifter stiffness (lb/in): ???? spring rate (lb/in) ???? seated spring force (lbs):??? same for Exhaust ....

08-08-2008, 12:51 PM	#3 (permalink)
Servin Beams Owners Group Join Date: Aug 2007 Location: DFW, Texas Posts: 1,250 Thanks: 13 Thanked 54 Times in 42 Posts iTrader Rating: (2/100% )	Wow lots of specifics you need there. Sadly i cant tell you anything but have you tried asking Mandalay. He has a translated service manual perhaps he can look up some values for you. I noticed Glen (Celica RA45) looked at this thread i would've figured he could help you on some of this...