where can i find a beams motor set??

drifterboy240 · 02-14-2007, 08:47 PM

okay i have been reading the site for a while now and finally decided to sign up and become a member, so anyways i have a offer for a MR-2 and dont know if i should let it go or not?? but anyways enough about that if i do get this MR-2 where could i find a beams motor, which brings me to my next comment i am a N/A lover. and this my friend is one h*** of a N/A motor just from what i have been reading.

canadam · 02-14-2007, 09:12 PM

There's often sets on eBay. Expect to pay $5000-6000 for a MR2-specific setup. It's definately the easiest way to get a BEAMS into an MR2.

PHOENIX · 02-14-2007, 11:01 PM

Welcome to the Beams Section!

a couple of places in the states to get them are

www.chicoraceworks.com
www.mr2warehouse.com

Ben · 02-14-2007, 11:51 PM

http://cgi.ebay.com/ebaymotors/JDM-9...mZ260077043974

EricLee7481 · 02-15-2007, 12:19 AM

Or you can buy mine

http://www.mr2board.com/forums/mk-2-...eams-swap.html

Eric

Ben · 02-15-2007, 12:31 AM

Quote:

Originally Posted by EricLee7481

Or you can buy mine

http://www.mr2board.com/forums/mk-2-...eams-swap.html

Eric

I WOULD!!!!

canadam · 02-15-2007, 01:06 PM

I stand corrected. This is the easiest way to get a BEAMS into an MR2.

What a gorgeous car!

Quote:

Originally Posted by EricLee7481

Or you can buy mine

http://www.mr2board.com/forums/mk-2-...eams-swap.html

Eric

drifterboy240 · 02-15-2007, 06:30 PM

yea looked at that car gorgeous but sadly enough not enough money for that kinda of MR-2 (i wish i did though)

drifterboy240 · 02-15-2007, 06:35 PM

ohh and the MR-2 that i might get is a 1991 MR-2 does that make it harder or easier to swap in the BEAMS motor???

PHOENIX · 02-15-2007, 06:44 PM

if your doing a full swap from a clip, doesnt help or hurt the time and difficulty of the swap.

drifterboy240 · 02-15-2007, 07:04 PM

okay thanks i guess i can relate it to doing an SR swap for my car if you got a clip the better off you are right or kinda right.

PHOENIX · 02-19-2007, 06:14 PM

yes, clips are much easier, its literally pulling one piece of the original and replacing it with the piece from the clip. its just really nice. I helped a buddy here do a swap with a clip, and it was the easiest engine job ive ever helped on.

drifterboy240 · 02-19-2007, 11:02 PM

thanks you guys have been helpfull

02-14-2007, 08:47 PM	#1 (permalink)
drifterboy240 No Skills Join Date: Feb 2007 Posts: 11 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	where can i find a beams motor set?? okay i have been reading the site for a while now and finally decided to sign up and become a member, so anyways i have a offer for a MR-2 and dont know if i should let it go or not?? but anyways enough about that if i do get this MR-2 where could i find a beams motor, which brings me to my next comment i am a N/A lover. and this my friend is one h*** of a N/A motor just from what i have been reading.

02-14-2007, 09:12 PM	#2 (permalink)
canadam MidshipExpress Join Date: Feb 2005 Location: Beautiful British Columbia Posts: 9,549 Thanks: 117 Thanked 129 Times in 112 Posts My Google Map iTrader Rating: (29/100% )	There's often sets on eBay. Expect to pay $5000-6000 for a MR2-specific setup. It's definately the easiest way to get a BEAMS into an MR2. __________________ WTB ASAP: Black Glove Box Surround - Not the box itself, but the dash plastics it sits in 3SGTE Upper Timing Belt Cover Driver's side seatback - must have bolster and lumbar adjustments, cover condition does not matter - will trade non-adjustable. Genuine Tom's Sides and Rear - replica kits not considered Frunk Plastics - no cracks Mechanical Gauge Cluster - KP/H preferred, but not required. Engine Bay X Brace

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-14-2007, 11:01 PM	#3 (permalink)
PHOENIX Beams Owners Group Join Date: Mar 2005 Location: On Hiatus....... Posts: 7,914 Thanks: 84 Thanked 260 Times in 197 Posts Blog Entries: 1 My Google Map iTrader Rating: (46/100% )	Welcome to the Beams Section! a couple of places in the states to get them are www.chicoraceworks.com www.mr2warehouse.com

02-14-2007, 11:51 PM	#4 (permalink)
Ben Same In The End Join Date: Aug 2006 Location: Oceanside, CA / Reno, NV Posts: 3,925 Thanks: 18 Thanked 276 Times in 258 Posts My Google Map iTrader Rating: (11/100% )	http://cgi.ebay.com/ebaymotors/JDM-9...mZ260077043974

02-15-2007, 12:19 AM	#5 (permalink)
EricLee7481 Beams Owners Group Join Date: Mar 2005 Posts: 160 Thanks: 1 Thanked 1 Time in 1 Post iTrader Rating: (6/100% )	Or you can buy mine http://www.mr2board.com/forums/mk-2-...eams-swap.html Eric

02-15-2007, 06:30 PM	#8 (permalink)
drifterboy240 No Skills Join Date: Feb 2007 Posts: 11 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	yea looked at that car gorgeous but sadly enough not enough money for that kinda of MR-2 (i wish i did though)

02-15-2007, 06:35 PM	#9 (permalink)
drifterboy240 No Skills Join Date: Feb 2007 Posts: 11 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	ohh and the MR-2 that i might get is a 1991 MR-2 does that make it harder or easier to swap in the BEAMS motor???

02-15-2007, 06:44 PM	#10 (permalink)
PHOENIX Beams Owners Group Join Date: Mar 2005 Location: On Hiatus....... Posts: 7,914 Thanks: 84 Thanked 260 Times in 197 Posts Blog Entries: 1 My Google Map iTrader Rating: (46/100% )	if your doing a full swap from a clip, doesnt help or hurt the time and difficulty of the swap.

02-15-2007, 07:04 PM	#11 (permalink)
drifterboy240 No Skills Join Date: Feb 2007 Posts: 11 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	okay thanks i guess i can relate it to doing an SR swap for my car if you got a clip the better off you are right or kinda right.

02-19-2007, 06:14 PM	#12 (permalink)
PHOENIX Beams Owners Group Join Date: Mar 2005 Location: On Hiatus....... Posts: 7,914 Thanks: 84 Thanked 260 Times in 197 Posts Blog Entries: 1 My Google Map iTrader Rating: (46/100% )	yes, clips are much easier, its literally pulling one piece of the original and replacing it with the piece from the clip. its just really nice. I helped a buddy here do a swap with a clip, and it was the easiest engine job ive ever helped on.

02-19-2007, 11:02 PM	#13 (permalink)
drifterboy240 No Skills Join Date: Feb 2007 Posts: 11 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	thanks you guys have been helpfull