4agze DLI w/ C50 tranny Question

M-r2d2 · 03-29-2009, 10:12 PM

so I got my swap done.
but when i'm doing around 60 70mph the rpm's are at like 4-5500rpm. I don't know for sure the speed but I was on a road that is 60 and I wasn't catching any body and no one was catching me so I had to be at around 60mph but my rpm's where close to 5K is this normal. and the little vent hole on the trans was spitting fluid everywhere but I think I over filled it.
I look in the toyota manual and it has the Maximum speed per gear listed, I'll post a pic. Its like driving in third gear on the high way or something but I know its in fifth cus I can down shift into 4th and the revs go way up. I thought the N/A trans and S/C trans differences was the first 4 gears and fifth was the same. or am I wrong do I still have to deal with the high rpm"s

If I go slow then 5th will be at like 4K but it still fills like I'm going slower than 60mph anyone know what my rpm's should be with the 85 mr2 trans??
sorry so long but please help!!!!

mr3 · 03-29-2009, 10:31 PM

I'm not sure about that tranny but with my stock set up. Bluetop in an 87 with a c52 I believe, my rpms are about 4-4.5k on highway in 5th gear.

M-r2d2 · 03-29-2009, 10:37 PM

ok
I'm used to driving my truck. at 70 its at like 2300rpm but i was expecting lower on the 2 my be like 3K or some thing
how is the pull in 5th I run out of gear relly quickly in like not ever 15 sec i'm out of 4th I can leave 3rd gear in about a 100 yards or a block and a half is this about right??

mr3 · 03-30-2009, 08:46 AM

Depends how hard you are pulling. Highways are fun cause It's like really quick change through all the gears. On ramps I hit in third then 4th then by the time I'm out, I'm in 5th. I hope I'm making sense I just woke up for class.

The kid I bought my silvertop said he had that transmission I could have but I didnt want it because he said I'd be doing like 60mph at 5k rpm's. I guess yours is about right with what that kid told me.

On a side note, I thought these things had a speed limiter thing so the top speed was like 113mph?

M-r2d2 · 03-30-2009, 09:46 PM

Well I have found the problem. I have a tach converter for the signal to be read by the old tach and it has to be calibrated the right way so I have to find out the right calibration I think I got it down now I'm at about 3-4K on highway

mr3 · 03-30-2009, 11:29 PM

Thats where it should be. Last resort would be an aftermarket tach. That's if you are in diar need of knowing your rpm's.

M-r2d2 · 03-31-2009, 07:58 AM

I do need to know my speedo doesn't work right now so I need something. and with an engine turning 7500rpm It's good to know.

Jackstand Queen · 04-08-2009, 12:22 PM

At 3800 RPM in 5th gear your speed should be 70 MPH. These are numbers from a oem c-52 Mr2.

M-r2d2 · 04-08-2009, 09:12 PM

hey thanks
I'm getting a cable friday
the guys at the yard are going to take it out I already have the middle cable but when the line broke I guess it got cough up in the line, so now I need the whole thing

03-29-2009, 10:12 PM	#1 (permalink)
M-r2d2 Cage Fighter Join Date: Apr 2007 Location: Decatur,TX Posts: 156 Thanks: 5 Thanked 3 Times in 3 Posts iTrader Rating: (1/100% )	4agze DLI w/ C50 tranny Question so I got my swap done. but when i'm doing around 60 70mph the rpm's are at like 4-5500rpm. I don't know for sure the speed but I was on a road that is 60 and I wasn't catching any body and no one was catching me so I had to be at around 60mph but my rpm's where close to 5K is this normal. and the little vent hole on the trans was spitting fluid everywhere but I think I over filled it. I look in the toyota manual and it has the Maximum speed per gear listed, I'll post a pic. Its like driving in third gear on the high way or something but I know its in fifth cus I can down shift into 4th and the revs go way up. I thought the N/A trans and S/C trans differences was the first 4 gears and fifth was the same. or am I wrong do I still have to deal with the high rpm"s If I go slow then 5th will be at like 4K but it still fills like I'm going slower than 60mph anyone know what my rpm's should be with the 85 mr2 trans?? sorry so long but please help!!!! Attached Thumbnails

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-29-2009, 10:31 PM	#2 (permalink)
mr3 Cage Fighter Join Date: Jun 2008 Location: Plymouth Mtg, Pa Posts: 840 Thanks: 19 Thanked 26 Times in 25 Posts iTrader Rating: (2/100% )	I'm not sure about that tranny but with my stock set up. Bluetop in an 87 with a c52 I believe, my rpms are about 4-4.5k on highway in 5th gear.

03-29-2009, 10:37 PM	#3 (permalink)
M-r2d2 Cage Fighter Join Date: Apr 2007 Location: Decatur,TX Posts: 156 Thanks: 5 Thanked 3 Times in 3 Posts iTrader Rating: (1/100% )	ok I'm used to driving my truck. at 70 its at like 2300rpm but i was expecting lower on the 2 my be like 3K or some thing how is the pull in 5th I run out of gear relly quickly in like not ever 15 sec i'm out of 4th I can leave 3rd gear in about a 100 yards or a block and a half is this about right??

03-30-2009, 08:46 AM	#4 (permalink)
mr3 Cage Fighter Join Date: Jun 2008 Location: Plymouth Mtg, Pa Posts: 840 Thanks: 19 Thanked 26 Times in 25 Posts iTrader Rating: (2/100% )	Depends how hard you are pulling. Highways are fun cause It's like really quick change through all the gears. On ramps I hit in third then 4th then by the time I'm out, I'm in 5th. I hope I'm making sense I just woke up for class. The kid I bought my silvertop said he had that transmission I could have but I didnt want it because he said I'd be doing like 60mph at 5k rpm's. I guess yours is about right with what that kid told me. On a side note, I thought these things had a speed limiter thing so the top speed was like 113mph?

03-30-2009, 09:46 PM	#5 (permalink)
M-r2d2 Cage Fighter Join Date: Apr 2007 Location: Decatur,TX Posts: 156 Thanks: 5 Thanked 3 Times in 3 Posts iTrader Rating: (1/100% )	Well I have found the problem. I have a tach converter for the signal to be read by the old tach and it has to be calibrated the right way so I have to find out the right calibration I think I got it down now I'm at about 3-4K on highway

03-30-2009, 11:29 PM	#6 (permalink)
mr3 Cage Fighter Join Date: Jun 2008 Location: Plymouth Mtg, Pa Posts: 840 Thanks: 19 Thanked 26 Times in 25 Posts iTrader Rating: (2/100% )	Thats where it should be. Last resort would be an aftermarket tach. That's if you are in diar need of knowing your rpm's.

03-31-2009, 07:58 AM	#7 (permalink)
M-r2d2 Cage Fighter Join Date: Apr 2007 Location: Decatur,TX Posts: 156 Thanks: 5 Thanked 3 Times in 3 Posts iTrader Rating: (1/100% )	I do need to know my speedo doesn't work right now so I need something. and with an engine turning 7500rpm It's good to know.

04-08-2009, 12:22 PM	#8 (permalink)
Jackstand Queen Cage Fighter Join Date: May 2008 Posts: 677 Thanks: 52 Thanked 56 Times in 53 Posts iTrader Rating: (1/100% )	At 3800 RPM in 5th gear your speed should be 70 MPH. These are numbers from a oem c-52 Mr2.

04-08-2009, 09:12 PM	#9 (permalink)
M-r2d2 Cage Fighter Join Date: Apr 2007 Location: Decatur,TX Posts: 156 Thanks: 5 Thanked 3 Times in 3 Posts iTrader Rating: (1/100% )	hey thanks I'm getting a cable friday the guys at the yard are going to take it out I already have the middle cable but when the line broke I guess it got cough up in the line, so now I need the whole thing