AutoLabLLC does fantastic work!

Aaron · 09-19-2006, 10:15 PM

I purchased varies parts for a turbo setup(precision sc44, tial wastegate, ats adapter plate). Once I had these parts I couldn't find anyone to fab me up a downpipe and a dumptube out of Stainless Steel. I was referred by Ty Saxon to contact Bill(Nocash) at AutoLab to see if he would do the work. He told me to send the parts in and he would do the work and then give me a price on cost. I wasn't worried about the cost since I needed this done and didn't mind if it was between 300-500. He charged me an extremely fair price and didn't use one of my flanges that I sent him because he didn't think it was strong enough so he used one of his own. I'm extremely pleased at the quality of his product and the quality of his welding abilities! For anyone who needs any mr2 parts I highly suggest to contact Bill at AutoLab. Here's their website for contact information: http://www.autolabonline.com/.

Here is a picture of his work on my car!
http://www.carpron.com/multisite/v/U...04111.JPG.html

PHOENIX · 09-19-2006, 10:21 PM

very nice to know that, thanks!

can I see a few more pictures? The ones you have are a little blurry.

Aaron · 09-19-2006, 11:21 PM

http://www.carpron.com/multisite/v/U...03972.JPG.html

That's the only other good picture I have of my engine bay. I'll have to take better ones when the car rolls out the garage after 2 years!

09-19-2006, 10:15 PM	#1 (permalink)
Aaron Banned Join Date: Feb 2005 Posts: 148 Thanks: 0 Thanked 1 Time in 1 Post iTrader Rating: (0/0% )	AutoLabLLC does fantastic work! I purchased varies parts for a turbo setup(precision sc44, tial wastegate, ats adapter plate). Once I had these parts I couldn't find anyone to fab me up a downpipe and a dumptube out of Stainless Steel. I was referred by Ty Saxon to contact Bill(Nocash) at AutoLab to see if he would do the work. He told me to send the parts in and he would do the work and then give me a price on cost. I wasn't worried about the cost since I needed this done and didn't mind if it was between 300-500. He charged me an extremely fair price and didn't use one of my flanges that I sent him because he didn't think it was strong enough so he used one of his own. I'm extremely pleased at the quality of his product and the quality of his welding abilities! For anyone who needs any mr2 parts I highly suggest to contact Bill at AutoLab. Here's their website for contact information: http://www.autolabonline.com/. Here is a picture of his work on my car! http://www.carpron.com/multisite/v/U...04111.JPG.html

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-19-2006, 10:21 PM	#2 (permalink)
PHOENIX Beams Owners Group Join Date: Mar 2005 Location: On Hiatus....... Posts: 9,266 Thanks: 92 Thanked 292 Times in 224 Posts Blog Entries: 1 My Google Map iTrader Rating: (49/100% )	very nice to know that, thanks! can I see a few more pictures? The ones you have are a little blurry.

09-19-2006, 11:21 PM	#3 (permalink)
Aaron Banned Join Date: Feb 2005 Posts: 148 Thanks: 0 Thanked 1 Time in 1 Post iTrader Rating: (0/0% )	http://www.carpron.com/multisite/v/U...03972.JPG.html That's the only other good picture I have of my engine bay. I'll have to take better ones when the car rolls out the garage after 2 years!