Detailing your MR2 Engine Bay Polishing Question

canadam · 09-03-2007, 07:53 PM

What have you guys used to polish up cast parts such as the coolant waterneck?

Sang · 09-03-2007, 08:54 PM

I used a small file to grind down the seams and any numbers, letters, et cetera.

I then used 220 grit+sanding block to remove the castings and further reshape any areas that need it.

I then use 320 grit, then 400 grit DRY (this kinda sucks cause the papers has to constantly be cleaned), 600 grit WET, then 1000 grit.

Afterwards, get a polishing compound and have at it.

I must stress that the first two stages of the process (filing+220 grit and 320 grit) are the most important. I did the plenum on a manifold over the summer, looked 100% better than it does stock, but no where near perfect. I will be getting a new stock manifold from Shaun and will be polishing up that for a 2nd attempt. This time i'm not stopping until it has a mirror finish

If you have a decent sized air compressor and die grinder. You can use 3M rolocs discs to remove the casting (course pad, then medium pad, then fine pad), then start going at it with 400 grit WET, et cetera.

canadam · 09-03-2007, 11:10 PM

Cool. Thanks

Ryansmagic · 09-04-2007, 05:24 PM

I start out with 80 grid, then 120 then 220 then 300 then 400 then 600 then 1000 then 2000
once I hit 600, I use dry then wet
then polish

09-03-2007, 07:53 PM	#1 (permalink)
canadam MidshipExpress Join Date: Feb 2005 Location: Beautiful British Columbia Posts: 10,399 Thanks: 120 Thanked 142 Times in 121 Posts My Google Map iTrader Rating: (34/100% )	Engine Bay Polishing Question What have you guys used to polish up cast parts such as the coolant waterneck? __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

LinkBacks (?) LinkBack to this Thread: http://www.mr2.com/forums/general-technical-discussion/Toyota-MR2-20695-engine-bay-polishing-question.html
Posted By	For	Type	Date
Toyota MR2 Message Board	This thread	Refback	09-04-2007 06:50 PM

09-03-2007, 08:54 PM	#2 (permalink)
Sang Turtle Join Date: Jul 2006 Location: FL Posts: 4,096 Thanks: 18 Thanked 267 Times in 246 Posts iTrader Rating: (5/100% )	I used a small file to grind down the seams and any numbers, letters, et cetera. I then used 220 grit+sanding block to remove the castings and further reshape any areas that need it. I then use 320 grit, then 400 grit DRY (this kinda sucks cause the papers has to constantly be cleaned), 600 grit WET, then 1000 grit. Afterwards, get a polishing compound and have at it. I must stress that the first two stages of the process (filing+220 grit and 320 grit) are the most important. I did the plenum on a manifold over the summer, looked 100% better than it does stock, but no where near perfect. I will be getting a new stock manifold from Shaun and will be polishing up that for a 2nd attempt. This time i'm not stopping until it has a mirror finish If you have a decent sized air compressor and die grinder. You can use 3M rolocs discs to remove the casting (course pad, then medium pad, then fine pad), then start going at it with 400 grit WET, et cetera.

09-03-2007, 11:10 PM	#3 (permalink)
canadam MidshipExpress Join Date: Feb 2005 Location: Beautiful British Columbia Posts: 10,399 Thanks: 120 Thanked 142 Times in 121 Posts My Google Map iTrader Rating: (34/100% )	Cool. Thanks

09-04-2007, 05:24 PM	#4 (permalink)
Ryansmagic No Skills Join Date: Oct 2005 Location: Wisconsin Posts: 111 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (4/100% )	I start out with 80 grid, then 120 then 220 then 300 then 400 then 600 then 1000 then 2000 once I hit 600, I use dry then wet then polish