MKII Rev 2 3SGTE Parts

RichieRichJP · 10-19-2009, 05:17 PM

Here's a list of parts I need for a 91-92 3SGTE.
I looked up these parts on ToyoDIY so hopefully they are the right part numbers

Notes:
-I'm doing a ground up full rebuild.
-Using TOGA Oil Pump, pin needed??
-Bolded prices were from quotes I searched

16283-88381 Hose From Hell $4. 36
16264-88383 Water Hose no. 3 $18.45
16341-88380 Water Outlet Gasket
96761-24017 By-Pass Pipe O-Ring $1.43
16258-88381 By-Pass Pipe Gasket
16325-62010 Water Inlet Housing Gasket
16282-88380 By-Pass Hose No. 5 $13.36
15197-63021 Oil Pump Gasket $3.71
90253-09001 Oil Pump Pin x2
16267-88382 By-Pass Hose No. 3 $15.60

15785-35010 Oil Cooler O-Ring
90301-52002 Oil Cooler O-Ring

All Oil Pump Bolts:
91611-60625 Oil Pump bolt x10
91611-60635 Oil Pump Bolt x 2

All Water pump bolts:
93220-16020
16193-88460 x2
91611-60625 x3
91642-80835
90116-10113 Exhaust manifold stud

16385-74020 Alternator Fan Belt Adjusting Slider
90119-08888 Bolt for above
Alternator bracket end plate
TRD Thermostat
All underbody Rubber plugs

All Bolts for the coolant bypass pipes:
91611-G0814
91651-G0816 2 needed or 1??
91512-60812 Lower Pipe bolt

All Shipped to 32571

te51levin · 10-22-2009, 08:25 PM

Sorry to keep you waiting, but and complicated requests like this sort of end up on the back burner. Even though you've supplied part numbers, there can be a lot of back-and forth involved to make sure that the numbers a customer provides are actually the parts he wants to buy. And you have to be VERY careful with ToyoDIY because, as useful as it is, it doesn't allow you to filter parts down to only the ones that apply to your particular combination.

You've certainly done your homework, but maybe a little more than necessary; the oil pump and water pump bolts don't normally need to be replaced. Even if you just have a fetish for shiny hardware, a new water pump (which I'd highly recommend, by the way) will come with almost all of the water pump hardware you've listed already installed.

I have no idea whether you'll need a pin with an aftermarket oil pump. If you're referring to 90253-09001, they don't come with a Toyota oil pump, but then they're not often removed from the block, so you don't normally have to replace them.

I've priced out the list, and updated part numbers where necessary:

16283-88381 - $4.36 - Hose From Hell
16264-88383 - $18.45 - Water Hose no. 3
16341-88381 - $5.69 - Water Outlet Gasket
96761-24017 - $1.43 - By-Pass Pipe O-Ring
16258-88381 - $3.58 - By-Pass Pipe Gasket
16325-62010 - $4.36 - Water Inlet Housing Gasket
16282-88380 - $13.36 - By-Pass Hose No. 5
15197-63021 - $3.86 - Oil Pump Gasket
90253-09001 - $0.99 - Oil Pump Pin x2
16267-88382 - $15.60 - By-Pass Hose No. 3

15785-35010 - $0.91 - Oil Cooler O-Ring
90301-52002 - $3.37 - Oil Cooler O-Ring

91611-B0625 - $0.53 - Oil Pump bolt x10
91611-60635 - $0.91 - Oil Pump Bolt x 2

93220-16020 - $0.61 - Screw
16193-88460 - $1.55 - Bolt x2
91611-B0625 - $0.53 - Bolt x3
90080-11499 - $0.68 - Bolt
90116-10113 - $1.27 - Exhaust manifold stud

16385-74020 - $3.37 - Alternator Fan Belt Adjusting Slider
90119-08888 - $1.35 - Bolt for above

You can't get the alternator bracket end plate without the entire alternator bracket:
12501-74040 - $95.16 - Alternator bracket, w/o power steering
12501-74050 - $105.94 - Alternator bracket, with power steering

PTR04-35050 - $68.40 - TRD Thermostat

"All underbody Rubber plugs" = literally about an hour's worth of detective work tracking down a huge list of parts that most people do not actually need. Can you narrow it down a little?

91611-60814 - $0.65 - Bolt
91651-G0816 - $0.87 - Bolt (qty not clear; please check vehicle)
91512-10166 - $0.69 - Lower Pipe bolt

I suspect that you will not literally want everything on the list, and shipping costs will depend heavily on what you actually order. Typically, though, you're looking at between $11 and $18 for a portion or all of the list above. It's all saved on quote number 50707, so we will work on that and edit it as necessary to get you what you need. Thanks man!

RichieRichJP · 10-23-2009, 07:15 AM

Thanks for the reply. I will be building from a built block (whenever I get it), but all of the timing components are missing.
I purchased all of the timing components and from several members on mr2oc and most of them did not include bolts, which was expected.
Those rubber underbody plugs, are various in size between 1" to about 1.5" in diameter. I can't think of any purpose for these except to drain water

I can take a picture of them if you need.
I'll make that plate for the alternator bracket then...

Also in regard to these part numbers, I'm going with a 5SGTE set up. From the information I have gathered, the only thing that get swapped out is the block, everything else stays 3S. Is this information correct?

Thanks again and I'll try call today and get this stuff ordered.

te51levin · 10-29-2009, 03:56 PM

Quote:

Originally Posted by RichieRichJP

Those rubber underbody plugs, are various in size between 1" to about 1.5" in diameter. I can't think of any purpose for these except to drain water

I can take a picture of them if you need.

Well, they're definitely drain plugs. My real concern is identifying which ones in particular you need, because there are tons of them all throughout the car. Because there aere so many, they're also scattered throughout the catalog. Most of them can be identified fairly easily by location. Where are the ones you are missing?

Quote:

Originally Posted by RichieRichJP

Also in regard to these part numbers, I'm going with a 5SGTE set up. From the information I have gathered, the only thing that get swapped out is the block, everything else stays 3S. Is this information correct?

From what I know, yes, it's just about that simple. There are always surprises when building or modifying things. Ask me how I know

RichieRichJP · 10-31-2009, 02:23 PM

ha!
Thanks for the info!
I need pretty much all of them located on the main body under the car. Pretty much under the seats, subwoofers etc.

te51levin · 11-03-2009, 03:08 PM

Quote:

Originally Posted by RichieRichJP

I need pretty much all of them located on the main body under the car. Pretty much under the seats, subwoofers etc.

If I understand you correctly, you just need the ones on the cabin floor. That saves a lot of work, because there are a bunch of them on the trunk floors, structural (frame) rails, etc, that we can ignore. Here are the ones in the floor of the passenger compartment:

90950-01867 - $2.56 - Plug, hole (big ones under floor)
90950-01181 - $2.51 - Plug, hole (tunnel and speaker floor)
90950-01426 - $2.34 - Plug, hole (rail under floor)

10-19-2009, 05:17 PM	#1 (permalink)
RichieRichJP Some Skills Join Date: Jul 2008 Location: Pace, Fl Posts: 52 Thanks: 3 Thanked 0 Times in 0 Posts iTrader Rating: (2/100% )	MKII Rev 2 3SGTE Parts Here's a list of parts I need for a 91-92 3SGTE. I looked up these parts on ToyoDIY so hopefully they are the right part numbers Notes: -I'm doing a ground up full rebuild. -Using TOGA Oil Pump, pin needed?? -Bolded prices were from quotes I searched 16283-88381 Hose From Hell $4. 36 16264-88383 Water Hose no. 3 $18.45 16341-88380 Water Outlet Gasket 96761-24017 By-Pass Pipe O-Ring $1.43 16258-88381 By-Pass Pipe Gasket 16325-62010 Water Inlet Housing Gasket 16282-88380 By-Pass Hose No. 5 $13.36 15197-63021 Oil Pump Gasket $3.71 90253-09001 Oil Pump Pin x2 16267-88382 By-Pass Hose No. 3 $15.60 15785-35010 Oil Cooler O-Ring 90301-52002 Oil Cooler O-Ring All Oil Pump Bolts: 91611-60625 Oil Pump bolt x10 91611-60635 Oil Pump Bolt x 2 All Water pump bolts: 93220-16020 16193-88460 x2 91611-60625 x3 91642-80835 90116-10113 Exhaust manifold stud 16385-74020 Alternator Fan Belt Adjusting Slider 90119-08888 Bolt for above Alternator bracket end plate TRD Thermostat All underbody Rubber plugs All Bolts for the coolant bypass pipes: 91611-G0814 91651-G0816 2 needed or 1?? 91512-60812 Lower Pipe bolt All Shipped to 32571

10-23-2009, 07:15 AM	#3 (permalink)
RichieRichJP Some Skills Join Date: Jul 2008 Location: Pace, Fl Posts: 52 Thanks: 3 Thanked 0 Times in 0 Posts iTrader Rating: (2/100% )	Thanks for the reply. I will be building from a built block (whenever I get it), but all of the timing components are missing. I purchased all of the timing components and from several members on mr2oc and most of them did not include bolts, which was expected. Those rubber underbody plugs, are various in size between 1" to about 1.5" in diameter. I can't think of any purpose for these except to drain water I can take a picture of them if you need. I'll make that plate for the alternator bracket then... Also in regard to these part numbers, I'm going with a 5SGTE set up. From the information I have gathered, the only thing that get swapped out is the block, everything else stays 3S. Is this information correct? Thanks again and I'll try call today and get this stuff ordered. Last edited by RichieRichJP; 10-23-2009 at 04:27 PM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-22-2009, 08:25 PM	#2 (permalink)
te51levin LithiaToyotaParts.com Join Date: Oct 2005 Location: Copperhead Road Posts: 3,683 Thanks: 50 Thanked 323 Times in 267 Posts My Google Map iTrader Rating: (193/100% )	Sorry to keep you waiting, but and complicated requests like this sort of end up on the back burner. Even though you've supplied part numbers, there can be a lot of back-and forth involved to make sure that the numbers a customer provides are actually the parts he wants to buy. And you have to be VERY careful with ToyoDIY because, as useful as it is, it doesn't allow you to filter parts down to only the ones that apply to your particular combination. You've certainly done your homework, but maybe a little more than necessary; the oil pump and water pump bolts don't normally need to be replaced. Even if you just have a fetish for shiny hardware, a new water pump (which I'd highly recommend, by the way) will come with almost all of the water pump hardware you've listed already installed. I have no idea whether you'll need a pin with an aftermarket oil pump. If you're referring to 90253-09001, they don't come with a Toyota oil pump, but then they're not often removed from the block, so you don't normally have to replace them. I've priced out the list, and updated part numbers where necessary: 16283-88381 - $4.36 - Hose From Hell 16264-88383 - $18.45 - Water Hose no. 3 16341-88381 - $5.69 - Water Outlet Gasket 96761-24017 - $1.43 - By-Pass Pipe O-Ring 16258-88381 - $3.58 - By-Pass Pipe Gasket 16325-62010 - $4.36 - Water Inlet Housing Gasket 16282-88380 - $13.36 - By-Pass Hose No. 5 15197-63021 - $3.86 - Oil Pump Gasket 90253-09001 - $0.99 - Oil Pump Pin x2 16267-88382 - $15.60 - By-Pass Hose No. 3 15785-35010 - $0.91 - Oil Cooler O-Ring 90301-52002 - $3.37 - Oil Cooler O-Ring 91611-B0625 - $0.53 - Oil Pump bolt x10 91611-60635 - $0.91 - Oil Pump Bolt x 2 93220-16020 - $0.61 - Screw 16193-88460 - $1.55 - Bolt x2 91611-B0625 - $0.53 - Bolt x3 90080-11499 - $0.68 - Bolt 90116-10113 - $1.27 - Exhaust manifold stud 16385-74020 - $3.37 - Alternator Fan Belt Adjusting Slider 90119-08888 - $1.35 - Bolt for above You can't get the alternator bracket end plate without the entire alternator bracket: 12501-74040 - $95.16 - Alternator bracket, w/o power steering 12501-74050 - $105.94 - Alternator bracket, with power steering PTR04-35050 - $68.40 - TRD Thermostat "All underbody Rubber plugs" = literally about an hour's worth of detective work tracking down a huge list of parts that most people do not actually need. Can you narrow it down a little? 91611-60814 - $0.65 - Bolt 91651-G0816 - $0.87 - Bolt (qty not clear; please check vehicle) 91512-10166 - $0.69 - Lower Pipe bolt I suspect that you will not literally want everything on the list, and shipping costs will depend heavily on what you actually order. Typically, though, you're looking at between $11 and $18 for a portion or all of the list above. It's all saved on quote number 50707, so we will work on that and edit it as necessary to get you what you need. Thanks man!

10-31-2009, 02:23 PM	#5 (permalink)
RichieRichJP Some Skills Join Date: Jul 2008 Location: Pace, Fl Posts: 52 Thanks: 3 Thanked 0 Times in 0 Posts iTrader Rating: (2/100% )	ha! Thanks for the info! I need pretty much all of them located on the main body under the car. Pretty much under the seats, subwoofers etc.