Electrical Problems 101

yikes · 03-02-2005, 09:27 PM

1.The alternator came with a plastic "hat" on the top post. If yours is gone, the wire harness will sit on the post and the post will dig into the wire harness. The result will be various malfunctions. It happened to me. The harness had a deep hole in it. I filled the hole with rtv and cured the problem.

2.The large white connector to the rear of the battery gets moisture. Pull apart (clean where necessary) and put it back together. This connector is associated with many electrical problems.

3.Remove the ground strap at the top of the tranny, Clean very well. Replace. Also remove the ground connection on the same cable where it connects to the body and clean. Best bet=replace the cable.

4.Starter electrical problems. Replace the positive cable. Most are corroded badly by now. Replace the smaller wire on the starter (ignition wire). This wire is also corroded badly and gets overheated by the exhaust. Don't fix, replace.

5.Remove and clean the ground wire close to the alternator. Adding additional ground straps is always a good idea.

6. Replacing the connector for the alternator top post is a good idea. Through the years of replacing alt. the wires tend to break at the connector.

7.The smaller wire on the battery positive cable is a fusible link. It should be replaced as age and corrosion can create all manner of problems.

8.Rule of thumb for electrical problems=it's the ground connection

9.Use a volt meter on the battery. Ignition off=12v engine running=13.5 to 14v.

10.Injector wire connectors sometimes pop off. A carefully placed dab of rtv between the connectors will hold them on.

Continue in numerical order.

canadam · 03-02-2005, 09:28 PM

11. If your car doesn't start after you washed it, there is likely water in the valley of the valve cover causing a short. Clean it out and try again.

NightRider88 · 05-17-2007, 12:43 AM

11.1. Do the same thing with the Distributor cap, remove, dry and put back into place.

Sam1 · 11-10-2007, 06:52 PM

12.
If three of your dash lights(just the engine cooling fan, charge, and brake) flash on or stay on while the car is turned on or while driving then test your alternator because it usually means it's bad!

03-02-2005, 09:27 PM	#1 (permalink)
yikes Cage Fighter Join Date: Feb 2005 Location: Gnaw Bone, Indiana Posts: 230 Thanks: 2 Thanked 11 Times in 3 Posts iTrader Rating: (0/0% )	Electrical Problems 101 1.The alternator came with a plastic "hat" on the top post. If yours is gone, the wire harness will sit on the post and the post will dig into the wire harness. The result will be various malfunctions. It happened to me. The harness had a deep hole in it. I filled the hole with rtv and cured the problem. 2.The large white connector to the rear of the battery gets moisture. Pull apart (clean where necessary) and put it back together. This connector is associated with many electrical problems. 3.Remove the ground strap at the top of the tranny, Clean very well. Replace. Also remove the ground connection on the same cable where it connects to the body and clean. Best bet=replace the cable. 4.Starter electrical problems. Replace the positive cable. Most are corroded badly by now. Replace the smaller wire on the starter (ignition wire). This wire is also corroded badly and gets overheated by the exhaust. Don't fix, replace. 5.Remove and clean the ground wire close to the alternator. Adding additional ground straps is always a good idea. 6. Replacing the connector for the alternator top post is a good idea. Through the years of replacing alt. the wires tend to break at the connector. 7.The smaller wire on the battery positive cable is a fusible link. It should be replaced as age and corrosion can create all manner of problems. 8.Rule of thumb for electrical problems=it's the ground connection 9.Use a volt meter on the battery. Ignition off=12v engine running=13.5 to 14v. 10.Injector wire connectors sometimes pop off. A carefully placed dab of rtv between the connectors will hold them on. Continue in numerical order.

03-02-2005, 09:28 PM	#2 (permalink)
canadam MidshipExpress Join Date: Feb 2005 Location: Beautiful British Columbia Posts: 9,549 Thanks: 117 Thanked 129 Times in 112 Posts My Google Map iTrader Rating: (29/100% )	11. If your car doesn't start after you washed it, there is likely water in the valley of the valve cover causing a short. Clean it out and try again. __________________ WTB ASAP: Black Glove Box Surround - Not the box itself, but the dash plastics it sits in 3SGTE Upper Timing Belt Cover Driver's side seatback - must have bolster and lumbar adjustments, cover condition does not matter - will trade non-adjustable. Genuine Tom's Sides and Rear - replica kits not considered Frunk Plastics - no cracks Mechanical Gauge Cluster - KP/H preferred, but not required. Engine Bay X Brace

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

LinkBacks (?) LinkBack to this Thread: http://www.mr2.com/forums/mk-1-mr2-aw11/Toyota-MR2-278-electrical-problems-101-a.html
Posted By	For	Type	Date
MR2 Technical Knowledgebase - Electrical Problems 101	This thread	Refback	08-22-2008 03:20 PM
MR2 Technical Knowledgebase	This thread	Refback	06-27-2008 12:10 PM

05-17-2007, 12:43 AM	#3 (permalink)
NightRider88 No Skills Join Date: May 2007 Posts: 23 Thanks: 0 Thanked 1 Time in 1 Post iTrader Rating: (0/0% )	11.1. Do the same thing with the Distributor cap, remove, dry and put back into place.

11-10-2007, 06:52 PM	#4 (permalink)
Sam1 Some Skills Join Date: Feb 2007 Posts: 76 Thanks: 6 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	12. If three of your dash lights(just the engine cooling fan, charge, and brake) flash on or stay on while the car is turned on or while driving then test your alternator because it usually means it's bad!