FS Mark 1 parts..big & small - Page 3

wude2 · 05-29-2009, 06:41 PM

ah awesome, yeah i am new to this forum. thanks for the info it'll definitely help me when i do find those pillars!

mhamrick · 05-30-2009, 08:37 PM

The 4AGE crank is not cast. They are all forged. The only difference is the size between the early (85-86) and the late (87+). There also was a very RARE few that had a 6 bolt flywheel but they are extremely extremely RARE. They also had all black lettering on the top.

Mr.Baca · 06-16-2009, 05:54 PM

do u have any non bent strut rod for r and l rear

mkimr2 · 06-17-2009, 12:08 PM

GZE injectors???

mr2tim · 06-19-2009, 01:25 PM

I do have a set of N/A injectors.

Do have misc GZE engine components. Fuel rails (different than N/A), intake manifold, Throttle, etc

Mr2 Tim

Quote:

Originally Posted by mkimr2

GZE injectors???

mr2tim · 06-19-2009, 01:26 PM

Check my PM to you.

Quote:

Originally Posted by Mr.Baca

do u have any non bent strut rod for r and l rear

mr2tim · 06-19-2009, 01:30 PM

Thanks for the info, I've got a crank under my work table (87) and will offer it for sale since the crank for S/C cars and N/A cars are the same.

Thanks

mr2tim

Quote:

Originally Posted by mhamrick

The 4AGE crank is not cast. They are all forged. The only difference is the size between the early (85-86) and the late (87+). There also was a very RARE few that had a 6 bolt flywheel but they are extremely extremely RARE. They also had all black lettering on the top.

mr2tim · 06-19-2009, 01:33 PM

Check my PM to you.

Quote:

Originally Posted by Mr.Baca

do u have any non bent strut rod for r and l rear

Tooljst8 · 08-10-2009, 08:16 PM

Looking for a dual or single belt crank pulley for a 88 NA. Have sent you a PM also.

Chris

Cano-07 · 08-10-2009, 08:33 PM

hey did you have the radio trim molding? send me a pic ! if u have it is the square frame of the radio & ac controls

stu4u3 · 08-25-2009, 09:34 PM

Hi. I'm interested in the fuel sender gauge (and gasket if you have it). Can you send a pic to me? Thanks.

jus7o · 08-27-2009, 06:36 PM

need both front bushing washers goes to a 86 mr2.

i circled what i need in blue. thanks

mr2tim · 08-27-2009, 06:56 PM

Black one is nice

, blue ones are abused

.

Have consoles, will ship?

Quote:

Originally Posted by Cano-07

hey did you have the radio trim molding? send me a pic ! if u have it is the square frame of the radio & ac controls

mr2tim · 09-06-2009, 08:18 AM

Previously sent you picture of a good Din 1 in Black? (and 2 recoverable blue ones)

Check your emails? Did you get?

Quote:

Originally Posted by Cano-07

hey did you have the radio trim molding? send me a pic ! if u have it is the square frame of the radio & ac controls

mr2tim · 09-06-2009, 08:19 AM

How's that sender gonna work for ya'll?

Quote:

Originally Posted by stu4u3

Hi. I'm interested in the fuel sender gauge (and gasket if you have it). Can you send a pic to me? Thanks.

mr2tim · 09-06-2009, 08:22 AM

Sent you RM response 9-6-09 7am

Thanks, Tim

mr2tim · 09-06-2009, 09:16 AM

Cut up my parts car like butter, (haven't had this much fun with my pants on for quite a while) and have several other misc new listings!!

As usual, I have pictures of everthing if you need 'em.

Thanks Yall

Tim (mr2tim)

Mark 1 parts add-on 9-6-09
**************************
Fuel Inj ballast 85-86
Air filter 87-89 (in the trunk)
Shelby 14” rims (trimmed in your color)
Pass seat, blue fabric, 87-89 series (new?)
Pass door, manual, 85-86 panel type, black, real pretty
Drs “ , “ , recoverable “
Door hinges (separate)
Replacement floor pans:
a. drs seat and forward floor
b. pass “ and “ “
c. front trunk
d. rear truck
Replacement drivers seat floor reinforcement beam w seat bolts
“ pass “ “ “ “ “
Complete battery holder bracket & base
Rt front axle assembly
a. lower arm
b. caliper
c. bearing carrier assembly
d. strut
Left front axle assembly
e. lower arm
f. caliper
g. bearing carrier assembly
h. strut

Rear valance-under the bumper with air breather holes
Rear panel- holds license plate and trunk latch
Electrical harness for chassis (include engine room fuse box)
Electrical engine harness for N/A engine
Fuse box (drivers foot area)
Complete steering column, ignition, blue wheel & lower U-joint
Dashboard reinforcement
Dashboard electrical harness (includes A/C hook-ups)
Automatic AT CV’s (half-shafts) both
Rt Rear axle assembly
a. Caliper
b. Bearing Carrier (N/A)
c. Forward Strut Bar
d. Toe-in adjuster
e. Lower control arm
f. Brake rotor
Left Rear axle assembly
g. Caliper
h. Bearing Carrier (N/A)
i. Forward Strut Bar
j. Toe-in adjuster
k. Lower control arm
l. Brake rotor
Chasis mounting bracket-rear 85-87
Chasis “ “ - rear 87-89 (these differ from 85-86)
Radiator lower support cradle/beam 85-86 (different than 87-89)

potatoe · 09-09-2009, 02:55 PM

what kinda shape's the complete 4age in?

aaron7 · 09-12-2009, 09:41 AM

I need:

mint black driver's side carpet
driver's side power window switch bezel
both black armrest door cups
mint black sunvisors
__________________

CodyS · 10-04-2009, 06:10 PM

Do you still have the right rear fender, if so how much to ship to 24179?
Also looking for passenger side front fender.

09-06-2009, 08:22 AM	#56 (permalink)
mr2tim SUPERcharZed ToyZ RacZer Join Date: Mar 2008 Location: South Florida Posts: 690 Thanks: 2 Thanked 41 Times in 38 Posts My Google Map iTrader Rating: (2/100% )	See my PM on your list request. Sent you RM response 9-6-09 7am Thanks, Tim

09-06-2009, 09:16 AM	#57 (permalink)
mr2tim SUPERcharZed ToyZ RacZer Join Date: Mar 2008 Location: South Florida Posts: 690 Thanks: 2 Thanked 41 Times in 38 Posts My Google Map iTrader Rating: (2/100% )	FS Mark 1 parts-new listing Cut up my parts car like butter, (haven't had this much fun with my pants on for quite a while) and have several other misc new listings!! As usual, I have pictures of everthing if you need 'em. Thanks Yall Tim (mr2tim) Mark 1 parts add-on 9-6-09 ************************** Fuel Inj ballast 85-86 Air filter 87-89 (in the trunk) Shelby 14” rims (trimmed in your color) Pass seat, blue fabric, 87-89 series (new?) Pass door, manual, 85-86 panel type, black, real pretty Drs “ , “ , recoverable “ Door hinges (separate) Replacement floor pans: a. drs seat and forward floor b. pass “ and “ “ c. front trunk d. rear truck Replacement drivers seat floor reinforcement beam w seat bolts “ pass “ “ “ “ “ Complete battery holder bracket & base Rt front axle assembly a. lower arm b. caliper c. bearing carrier assembly d. strut Left front axle assembly e. lower arm f. caliper g. bearing carrier assembly h. strut Rear valance-under the bumper with air breather holes Rear panel- holds license plate and trunk latch Electrical harness for chassis (include engine room fuse box) Electrical engine harness for N/A engine Fuse box (drivers foot area) Complete steering column, ignition, blue wheel & lower U-joint Dashboard reinforcement Dashboard electrical harness (includes A/C hook-ups) Automatic AT CV’s (half-shafts) both Rt Rear axle assembly a. Caliper b. Bearing Carrier (N/A) c. Forward Strut Bar d. Toe-in adjuster e. Lower control arm f. Brake rotor Left Rear axle assembly g. Caliper h. Bearing Carrier (N/A) i. Forward Strut Bar j. Toe-in adjuster k. Lower control arm l. Brake rotor Chasis mounting bracket-rear 85-87 Chasis “ “ - rear 87-89 (these differ from 85-86) Radiator lower support cradle/beam 85-86 (different than 87-89) Attached Thumbnails

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-29-2009, 06:41 PM	#41 (permalink)
wude2 No Skills Join Date: May 2009 Posts: 3 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	ah awesome, yeah i am new to this forum. thanks for the info it'll definitely help me when i do find those pillars!

05-30-2009, 08:37 PM	#42 (permalink)
mhamrick Some Skills Join Date: May 2009 Posts: 51 Thanks: 1 Thanked 3 Times in 3 Posts iTrader Rating: (0/0% )	The 4AGE crank is not cast. They are all forged. The only difference is the size between the early (85-86) and the late (87+). There also was a very RARE few that had a 6 bolt flywheel but they are extremely extremely RARE. They also had all black lettering on the top.

06-16-2009, 05:54 PM	#43 (permalink)
Mr.Baca No Skills Join Date: Jun 2009 Posts: 36 Thanks: 4 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	do u have any non bent strut rod for r and l rear

06-17-2009, 12:08 PM	#44 (permalink)
mkimr2 No Skills Join Date: Jun 2009 Posts: 12 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	GZE injectors???

08-10-2009, 08:16 PM	#49 (permalink)
Tooljst8 Rust Fight Go! Join Date: May 2009 Location: NY Posts: 39 Thanks: 5 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	Looking for a dual or single belt crank pulley for a 88 NA. Have sent you a PM also. Chris

08-10-2009, 08:33 PM	#50 (permalink)
Cano-07 No Skills Join Date: Nov 2008 Location: florida Posts: 11 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	hey did you have the radio trim molding? send me a pic ! if u have it is the square frame of the radio & ac controls

08-25-2009, 09:34 PM	#51 (permalink)
stu4u3 Fixing up a 1989 MR2 MK1 Join Date: Mar 2009 Location: Dallas/Fort Worth Posts: 249 Thanks: 10 Thanked 3 Times in 3 Posts iTrader Rating: (1/100% )	Hi. I'm interested in the fuel sender gauge (and gasket if you have it). Can you send a pic to me? Thanks.

08-27-2009, 06:36 PM	#52 (permalink)
jus7o D I Y Join Date: May 2007 Location: Houston Posts: 143 Thanks: 16 Thanked 1 Time in 1 Post iTrader Rating: (0/0% )	need both front bushing washers goes to a 86 mr2. i circled what i need in blue. thanks

09-09-2009, 02:55 PM	#58 (permalink)
potatoe No Skills Join Date: Jun 2009 Location: san marcos, ca Posts: 46 Thanks: 1 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	what kinda shape's the complete 4age in?

09-12-2009, 09:41 AM	#59 (permalink)
aaron7 omg jdm Join Date: Nov 2006 Location: MA, USA Posts: 53 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	I need: mint black driver's side carpet driver's side power window switch bezel both black armrest door cups mint black sunvisors __________________

10-04-2009, 06:10 PM	#60 (permalink)
CodyS No Skills Join Date: Sep 2009 Location: Bedford, Va Posts: 2 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	Do you still have the right rear fender, if so how much to ship to 24179? Also looking for passenger side front fender.