idle at 2k im going crazy! replaced the following and have the codes.... - Page 2

fvillota · 03-16-2009, 02:26 PM

well like i said! lol its either ****ed up. or it was clogged to hell making my car run a bit hotter cuz the temp arrow wont make it to the middle its tilted down and it never did that before.

mr2stealth · 03-18-2009, 01:26 PM

Well my idle is still ****ed up! I donno what to do, I made a video of it. But cant find it. And I really need to find out what it is because its making me crazy!!!!

fvillota · 03-18-2009, 01:27 PM

did you clean and do what i did? where ur timing at?

fvillota · 04-03-2009, 09:53 AM

well guess what! uits back to 2k.
what the f**** do all mr2's do this? ive never seen a fing celica do this!

CBR>MR2 · 04-10-2009, 12:25 AM

Quote:

Originally Posted by fvillota

OK. so i bought a new throttle body gasket ($2.50) i bought carb cleaner ($2.99) i bought the idle air control valve gasket on line because no one had it ($5.00 shipped)

You dont have the part number for both gaskets do you? Also, where did you bought it from? Thanks

fvillota · 04-10-2009, 11:37 AM

Toyota Camry Idle Control Valve - Car Parts Wholesale
this is where i got the idle air control gasket

and i the throttle body gasket they had in stock at the autozone by my house. hope i could help.

CBR>MR2 · 04-11-2009, 01:30 AM

thanks

fvillota · 04-11-2009, 05:29 PM

no problem.

Primera · 04-27-2009, 10:48 PM

Well I know that my throttle valve is quite worn and air leaks past it, like almost all the way around it. You might wanna check yours out too, although since its erratic in your situation, that doesnt sound likely to be your issue

fvillota · 04-27-2009, 11:59 PM

yea Ive checked and its fine. but thanks for the input all advice counts!

timbuck4 · 05-05-2009, 05:27 PM

I have this problem with my 91 N/A as well but not all the time. If I engage the clutch and give it a little gas the RPM's drop to around 1k until I shift again. Just got the car about 2 months ago and not sure if a tune up would help or not.

shimric · 05-06-2009, 09:09 PM

I replaced my ISCV and it dropped to 750rpm. It would make sense to replace something that basically controls the idle speed. Those things are like 16+ years old, just cleaning them out isn't going to do the job. With all that crap blowing back into the intake it's only a matter of time before it clogs again. Your best bet, if I were you, I would replace it, then do a breather reroute. Actually I did do that when I had my 2. Never had a problem with idle.

ebouwman · 05-06-2009, 09:15 PM

where would you re-route the breather to then shimric?

shimric · 05-06-2009, 09:27 PM

Quote:

Originally Posted by ebouwman

where would you re-route the breather to then shimric?

Uh, Don't make me dig all that up. From what my memory tells me.. (this is going to be extremely brief) Buy some rubber oil hose from autozone, buy this Craftsman air compressor purifier (look on sears.com) Instead of the oil blowing back into the throttle body it'll blow into the filter. You can just empty it out every now and then.

Again, it's been years since I've talked about this, but that's the gist of it.

Basically like this...
Buell Motorcycle Forum: Archive through April 05, 2009
Yea, it's a bike, I can remember that because I have it on my buell.

1stgen · 06-01-2009, 01:40 AM

Oil catch can...Pictures the old school air compressor purifier is what I used to use on my old American Muscle cars :P

1stgen · 06-01-2009, 01:54 AM

Another thing...why is there all those Vacuum lines plugged off at the back of our manifold..gives us some place to hook up a boost gauge? :P

fvillota · 06-01-2009, 07:31 AM

lol yea extra vac lines you can hook up

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-16-2009, 02:26 PM	#21 (permalink)
fvillota Cage Fighter Join Date: Feb 2008 Location: MIami Posts: 1,832 Thanks: 65 Thanked 28 Times in 28 Posts iTrader Rating: (6/100% )	well like i said! lol its either ****ed up. or it was clogged to hell making my car run a bit hotter cuz the temp arrow wont make it to the middle its tilted down and it never did that before.

03-18-2009, 01:26 PM	#22 (permalink)
mr2stealth Gett Sidewayz Join Date: May 2007 Location: Colorado Springs/Pueblo, Colorado Posts: 598 Thanks: 11 Thanked 3 Times in 3 Posts iTrader Rating: (0/0% )	Well my idle is still ****ed up! I donno what to do, I made a video of it. But cant find it. And I really need to find out what it is because its making me crazy!!!!

03-18-2009, 01:27 PM	#23 (permalink)
fvillota Cage Fighter Join Date: Feb 2008 Location: MIami Posts: 1,832 Thanks: 65 Thanked 28 Times in 28 Posts iTrader Rating: (6/100% )	did you clean and do what i did? where ur timing at?

04-03-2009, 09:53 AM	#24 (permalink)
fvillota Cage Fighter Join Date: Feb 2008 Location: MIami Posts: 1,832 Thanks: 65 Thanked 28 Times in 28 Posts iTrader Rating: (6/100% )	well guess what! uits back to 2k. what the f**** do all mr2's do this? ive never seen a fing celica do this!

04-10-2009, 11:37 AM	#26 (permalink)
fvillota Cage Fighter Join Date: Feb 2008 Location: MIami Posts: 1,832 Thanks: 65 Thanked 28 Times in 28 Posts iTrader Rating: (6/100% )	Toyota Camry Idle Control Valve - Car Parts Wholesale this is where i got the idle air control gasket and i the throttle body gasket they had in stock at the autozone by my house. hope i could help.

04-11-2009, 01:30 AM	#27 (permalink)
CBR>MR2 No Skills Join Date: Mar 2009 Posts: 13 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (1/100% )	thanks

04-11-2009, 05:29 PM	#28 (permalink)
fvillota Cage Fighter Join Date: Feb 2008 Location: MIami Posts: 1,832 Thanks: 65 Thanked 28 Times in 28 Posts iTrader Rating: (6/100% )	no problem.

04-27-2009, 10:48 PM	#29 (permalink)
Primera Cage Fighter Join Date: Aug 2007 Location: Mohave Valley, AZ Posts: 105 Thanks: 15 Thanked 2 Times in 2 Posts iTrader Rating: (3/100% )	Well I know that my throttle valve is quite worn and air leaks past it, like almost all the way around it. You might wanna check yours out too, although since its erratic in your situation, that doesnt sound likely to be your issue

04-27-2009, 11:59 PM	#30 (permalink)
fvillota Cage Fighter Join Date: Feb 2008 Location: MIami Posts: 1,832 Thanks: 65 Thanked 28 Times in 28 Posts iTrader Rating: (6/100% )	yea Ive checked and its fine. but thanks for the input all advice counts!

05-05-2009, 05:27 PM	#31 (permalink)
timbuck4 No Skills Join Date: Apr 2009 Posts: 10 Thanks: 0 Thanked 2 Times in 2 Posts iTrader Rating: (1/100% )	I have this problem with my 91 N/A as well but not all the time. If I engage the clutch and give it a little gas the RPM's drop to around 1k until I shift again. Just got the car about 2 months ago and not sure if a tune up would help or not.

05-06-2009, 09:09 PM	#32 (permalink)
shimric Führer of OT!!! Join Date: Apr 2006 Location: South Carolina Posts: 1,394 Thanks: 40 Thanked 45 Times in 38 Posts Blog Entries: 1 iTrader Rating: (0/0% )	I replaced my ISCV and it dropped to 750rpm. It would make sense to replace something that basically controls the idle speed. Those things are like 16+ years old, just cleaning them out isn't going to do the job. With all that crap blowing back into the intake it's only a matter of time before it clogs again. Your best bet, if I were you, I would replace it, then do a breather reroute. Actually I did do that when I had my 2. Never had a problem with idle.

05-06-2009, 09:15 PM	#33 (permalink)
ebouwman Curve Hugger Join Date: Jan 2009 Location: BC, Canada Posts: 1,390 Thanks: 18 Thanked 48 Times in 48 Posts My Google Map iTrader Rating: (0/0% )	where would you re-route the breather to then shimric?

06-01-2009, 01:40 AM	#35 (permalink)
1stgen Yup Join Date: Aug 2008 Location: Central Coast CA Posts: 383 Thanks: 11 Thanked 12 Times in 11 Posts My Google Map iTrader Rating: (1/100% )	Oil catch can...Pictures the old school air compressor purifier is what I used to use on my old American Muscle cars :P

06-01-2009, 01:54 AM	#36 (permalink)
1stgen Yup Join Date: Aug 2008 Location: Central Coast CA Posts: 383 Thanks: 11 Thanked 12 Times in 11 Posts My Google Map iTrader Rating: (1/100% )	Another thing...why is there all those Vacuum lines plugged off at the back of our manifold..gives us some place to hook up a boost gauge? :P

06-01-2009, 07:31 AM	#37 (permalink)
fvillota Cage Fighter Join Date: Feb 2008 Location: MIami Posts: 1,832 Thanks: 65 Thanked 28 Times in 28 Posts iTrader Rating: (6/100% )	lol yea extra vac lines you can hook up