Changing front turn signal bulb?

BCMikeMR2 · 01-06-2007, 07:45 PM

How do I change the front turn signal bulb,

the one on the front fender. I know how to get the light out at the front, this is the side one on the front fender. Sorry if this is a stupid question!

AndrewMcG · 01-06-2007, 09:07 PM

Reach your hand up underneath there and grab the back of the bulb or right where the wires meet the plastic clip with the bulb. Twist it and pull it out.

BCMikeMR2 · 01-07-2007, 12:22 AM

no place to put my hand up, do I have to remove the plastic covers underneath the car? or the one in the wheel well? Also how does the whole assembly come out? Is it bolted in from behind?

Just Wong It · 01-07-2007, 02:16 PM

i think its the wheel well plastic part.

Brokenline · 01-07-2007, 09:22 PM

if you cant go from underneath then go through the whell well, you dont have to remove the whole thing, just enough to get your hand in. and yes the moulding is bolted from behind.

-paul

CyFi · 01-08-2007, 03:05 AM

just pull the lights out, i forgot how but just pry it from the center of the car i believe and the whole fixture comes out, ive done it before so i know it works

01-06-2007, 07:45 PM	#1 (permalink)
BCMikeMR2 91 MR2 GLimited NA Join Date: Dec 2006 Location: Victoria BC Posts: 34 Thanks: 1 Thanked 1 Time in 1 Post My Google Map iTrader Rating: (0/0% )	Changing front turn signal bulb? How do I change the front turn signal bulb, the one on the front fender. I know how to get the light out at the front, this is the side one on the front fender. Sorry if this is a stupid question!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-06-2007, 09:07 PM	#2 (permalink)
AndrewMcG Its not lag, Its foreplay Join Date: Feb 2005 Location: Albuquerque Posts: 756 Thanks: 6 Thanked 19 Times in 17 Posts My Google Map iTrader Rating: (3/100% )	Reach your hand up underneath there and grab the back of the bulb or right where the wires meet the plastic clip with the bulb. Twist it and pull it out.

01-07-2007, 12:22 AM	#3 (permalink)
BCMikeMR2 91 MR2 GLimited NA Join Date: Dec 2006 Location: Victoria BC Posts: 34 Thanks: 1 Thanked 1 Time in 1 Post My Google Map iTrader Rating: (0/0% )	no place to put my hand up, do I have to remove the plastic covers underneath the car? or the one in the wheel well? Also how does the whole assembly come out? Is it bolted in from behind?

01-07-2007, 02:16 PM	#4 (permalink)
Just Wong It Toyota Join Date: Feb 2005 Location: Atlanta,Ga Posts: 1,397 Thanks: 8 Thanked 16 Times in 10 Posts My Google Map iTrader Rating: (2/100% )	i think its the wheel well plastic part.

01-07-2007, 09:22 PM	#5 (permalink)
Brokenline Cage Fighter Join Date: Feb 2005 Location: socal Posts: 284 Thanks: 2 Thanked 2 Times in 2 Posts iTrader Rating: (1/100% )	if you cant go from underneath then go through the whell well, you dont have to remove the whole thing, just enough to get your hand in. and yes the moulding is bolted from behind. -paul

01-08-2007, 03:05 AM	#6 (permalink)
CyFi Moved on Join Date: Oct 2005 Location: Phoenix Posts: 1,401 Thanks: 12 Thanked 38 Times in 35 Posts iTrader Rating: (11/100% )	just pull the lights out, i forgot how but just pry it from the center of the car i believe and the whole fixture comes out, ive done it before so i know it works