Liquidation Sale...Strong USD = Cheap V6 parts!

Weasy2k · 03-07-2009, 02:39 PM

(Taken from Sea2Sky Tuning - Home)
Hey everybody,
First off I must apologize to everyone out there for the constant delays in responses/jobs & orders. I am trying my best to get everything done and help everyone out .
Due to these unforeseen economic events and personal issues I am now liquidating most of my products to help get back on my feet here.
Since the Canadian Dollar is getting weaker (or shall i say the USD is getting stronger ) now is the best time to get the best deals possible!

Below is a list of products & prices of everything left
Please note that all prices are not FIRM, if you want to get more then 1 product feel free to message me (goto the contact us page) and we can go from there!

Arias V6 Piston Sets:
Custom made for Sea2Sky Tuning by Arias, these pistons are built to handle almost anything you can throw at them (Turbo, S/C, NO2). All motor users should contact us about special light weight piston sets.

More info can be found HERE

I currently have quite a few 5vz-fe and 3vz-fe piston sets in stock and have DRASTICALLY reduced my price below cost!

Applications:
In stock I have:
5vz-fe STOCK CR [9.5:1] Oversized Pistons .050: 1 Set Left!
3vz-fe STOCK CR Stock sized pistons: 2 Sets left

Regular Price: $850usd
Blow Out Price: $500usd + shipping
Liquidated Price: $400usd SHIPPED

High-Flo Valves:
All Sea2SkyTuning valves feature Manley Performance "Pro-Flo" design which cuts the stem of the valves back near the face to improve flow as much as 125% at .100" lift or to a max of 40% at full lift!

With this design you can get the flow rate of a 1mm OS valve minus the costly process of fitting a 1mm OS valve into the engine!

More information can be found at: High Flo Valves

Applications:
3/1mz-fe: Stock length or assorted valve tip lengths available. [.025”, .040”]
5/3vz-fe: SOLD OUT

List Price: $475 a set
Blow-Out Price: $325 per set
NEW price: $280 per set

ALL VALVES ABOVE ARE IN STOCK!! LIMITED QUANTITIES AVAILABLE!

Stage 1 Valve Springs:
Rated at 80lbs of pressure these springs will be able to handle higher boost and rpm levels vs the stock softer springs.

1 set of 1mz valve springs left! I may be able to get more at the prices listed below but only if there is demand for it.

Applications:
1/3mz-fe: SOLD OUT
3/5vz-fe: SOLD OUT

List $140 Blow out $100 a set!

Last Set $75!

Thank you!

-Johnny Riglietti
Owner/Operator
Sea2Sky Tuning

U-235 · 03-10-2009, 01:07 PM

And here you are again, tempting me with pistons...

Weasy2k · 03-10-2009, 11:10 PM

U-235 · 03-11-2009, 01:44 AM

I guess there's no sense resisting. :P

If you can hang onto a 5VZ set, I can order them when I get paid on Friday.

5vzbound · 03-31-2009, 10:38 PM

how many sets are left? how long will the sale last? i know i will have my money by te end of the month!

Weasy2k · 04-01-2009, 01:13 AM

I have sold out of 5vz valve sets. Have some 1mz valve sets left.

Running low on 3/5vz piston sets as well.

brad d · 04-20-2009, 06:47 PM

Thanks for the pistons, they look super good

3VZ-FE · 04-22-2009, 03:56 PM

Possible to shave them 3vz pistons safely down to a decent cr, like 8,8-9....? What distance is it between the top of the piston and down to the top/first ring?

Weasy2k · 04-25-2009, 01:11 PM

I am just about to start moving so i wont have any of that kind of info handy. Maybe in a bout a week i can help you out.

Why do you want to goto 9 anyway? How much PSI you looking to pump into the motor?

Oteck · 04-25-2009, 01:23 PM

save one .90" Hi-flow valves for me next weekend, will be in the shop or your out of town?

johnny g · 04-26-2009, 07:05 AM

Johnny, what have you got left for the 3VZ and the 1MZ? What prices?

3VZ-FE · 04-29-2009, 05:55 PM

Quote:

Originally Posted by Weasy2k

I am just about to start moving so i wont have any of that kind of info handy. Maybe in a bout a week i can help you out.

Why do you want to goto 9 anyway? How much PSI you looking to pump into the motor?

14-15 psi should do the trick.

Thing is if i go for the 1mm ferrdai HG's which is 0,3mm lower than stock, CR rise to 9,8-9,9. If it's possible to shave 1 mm off the pistons i should be close to 9,0 which is sweet.

Feel free to calculate my guesstimates btw :-P

thwam · 05-08-2009, 03:21 AM

Weasy, do you still have 5VZ pistons available? Thanks!

Todd

Weasy2k · 05-09-2009, 11:24 PM

Quote:

Originally Posted by 3VZ-FE

14-15 psi should do the trick.

Thing is if i go for the 1mm ferrdai HG's which is 0,3mm lower than stock, CR rise to 9,8-9,9. If it's possible to shave 1 mm off the pistons i should be close to 9,0 which is sweet.

Feel free to calculate my guesstimates btw :-P

Yes you can but there is no guarantees from Arias as per my rep.

Weasy2k · 05-09-2009, 11:26 PM

Hey everyone. Sorry about delays in response, i am in the middle of moving and the cable company are taking thier sweet arse time making the switch. Should be back online just after the 15th.

U-235 · 05-14-2009, 08:14 PM

Hey Johnny I had a quick question about the valves. My mechanically inclined friend said that sometimes valves need to be machined to fit in the appropriate head. The 5vz standard length valves are just plug-n-play, right? No additional work required?

Thanks so much for all your help!

Weasy2k · 05-17-2009, 02:48 PM

tHE only thing you would need to do is make sure the valve clearance to the cams is ok. Standard procedure, but no big machining needed at all.

sav234 · 05-27-2009, 12:07 PM

Hey mate do you have any rods and pistons for the 1mz? Im looking to buy 2 sets and if possible some valves and springs.

johnny g · 07-02-2009, 06:33 AM

Any update on our conversations mate?

5vzbound · 07-09-2009, 02:39 AM

are the vavles and springs gone for good? if so where can i track them down. I have the pistons, now its time for valves springs and cams

03-07-2009, 02:39 PM	#1 (permalink)
Weasy2k 3.4L 10K RPM In the works Join Date: Mar 2005 Location: Vancouver, BC Posts: 8,895 Thanks: 34 Thanked 80 Times in 66 Posts iTrader Rating: (9/100% )	Liquidation Sale...Strong USD = Cheap V6 parts! (Taken from Sea2Sky Tuning - Home) Hey everybody, First off I must apologize to everyone out there for the constant delays in responses/jobs & orders. I am trying my best to get everything done and help everyone out . Due to these unforeseen economic events and personal issues I am now liquidating most of my products to help get back on my feet here. Since the Canadian Dollar is getting weaker (or shall i say the USD is getting stronger ) now is the best time to get the best deals possible! Below is a list of products & prices of everything left Please note that all prices are not FIRM, if you want to get more then 1 product feel free to message me (goto the contact us page) and we can go from there! Arias V6 Piston Sets: Custom made for Sea2Sky Tuning by Arias, these pistons are built to handle almost anything you can throw at them (Turbo, S/C, NO2). All motor users should contact us about special light weight piston sets. More info can be found HERE I currently have quite a few 5vz-fe and 3vz-fe piston sets in stock and have DRASTICALLY reduced my price below cost! Applications: In stock I have: 5vz-fe STOCK CR [9.5:1] Oversized Pistons .050: 1 Set Left! 3vz-fe STOCK CR Stock sized pistons: 2 Sets left Regular Price: $850usd Blow Out Price: $500usd + shipping Liquidated Price: $400usd SHIPPED High-Flo Valves: All Sea2SkyTuning valves feature Manley Performance "Pro-Flo" design which cuts the stem of the valves back near the face to improve flow as much as 125% at .100" lift or to a max of 40% at full lift! With this design you can get the flow rate of a 1mm OS valve minus the costly process of fitting a 1mm OS valve into the engine! More information can be found at: High Flo Valves Applications: 3/1mz-fe: Stock length or assorted valve tip lengths available. [.025”, .040”] 5/3vz-fe: SOLD OUT List Price: $475 a set Blow-Out Price: $325 per set NEW price: $280 per set ALL VALVES ABOVE ARE IN STOCK!! LIMITED QUANTITIES AVAILABLE! Stage 1 Valve Springs: Rated at 80lbs of pressure these springs will be able to handle higher boost and rpm levels vs the stock softer springs. 1 set of 1mz valve springs left! I may be able to get more at the prices listed below but only if there is demand for it. Applications: 1/3mz-fe: SOLD OUT 3/5vz-fe: SOLD OUT List $140 Blow out $100 a set! Last Set $75! Thank you! -Johnny Riglietti Owner/Operator Sea2Sky Tuning __________________ -Johnny @ Sea2Sky Tuning - www.sea2skytuning.com http://www.mr2.com/forums/sea2sky-tu...-out-sale.html Last edited by Weasy2k; 05-17-2009 at 02:53 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

LinkBacks (?) LinkBack to this Thread: http://www.mr2.com/forums/sea2sky-tuning/Toyota-MR2-39088-liquidation-sale-strong-usd-cheap-v6-parts.html
Posted By	For	Type	Date
MR2 AUSTRALIA - 1MZ-FE N/A build -> 100hp/L	This thread	Refback	05-27-2009 06:47 PM

03-10-2009, 01:07 PM	#2 (permalink)
U-235 E=mr2 Join Date: Jun 2007 Location: In the back, where no one sees me. Posts: 302 Thanks: 13 Thanked 4 Times in 4 Posts iTrader Rating: (12/100% )	And here you are again, tempting me with pistons...

03-10-2009, 11:10 PM	#3 (permalink)
Weasy2k 3.4L 10K RPM In the works Join Date: Mar 2005 Location: Vancouver, BC Posts: 8,895 Thanks: 34 Thanked 80 Times in 66 Posts iTrader Rating: (9/100% )

03-11-2009, 01:44 AM	#4 (permalink)
U-235 E=mr2 Join Date: Jun 2007 Location: In the back, where no one sees me. Posts: 302 Thanks: 13 Thanked 4 Times in 4 Posts iTrader Rating: (12/100% )	I guess there's no sense resisting. :P If you can hang onto a 5VZ set, I can order them when I get paid on Friday.

03-31-2009, 10:38 PM	#5 (permalink)
5vzbound No Skills Join Date: Feb 2008 Posts: 35 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (1/100% )	how many sets are left? how long will the sale last? i know i will have my money by te end of the month!

04-01-2009, 01:13 AM	#6 (permalink)
Weasy2k 3.4L 10K RPM In the works Join Date: Mar 2005 Location: Vancouver, BC Posts: 8,895 Thanks: 34 Thanked 80 Times in 66 Posts iTrader Rating: (9/100% )	I have sold out of 5vz valve sets. Have some 1mz valve sets left. Running low on 3/5vz piston sets as well.

04-20-2009, 06:47 PM	#7 (permalink)
brad d Cage Fighter Join Date: Jul 2007 Posts: 112 Thanks: 0 Thanked 3 Times in 3 Posts iTrader Rating: (0/0% )	Thanks for the pistons, they look super good

04-22-2009, 03:56 PM	#8 (permalink)
3VZ-FE Some Skills Join Date: Oct 2005 Location: Norway Posts: 204 Thanks: 9 Thanked 3 Times in 3 Posts iTrader Rating: (0/0% )	Possible to shave them 3vz pistons safely down to a decent cr, like 8,8-9....? What distance is it between the top of the piston and down to the top/first ring?

04-25-2009, 01:11 PM	#9 (permalink)
Weasy2k 3.4L 10K RPM In the works Join Date: Mar 2005 Location: Vancouver, BC Posts: 8,895 Thanks: 34 Thanked 80 Times in 66 Posts iTrader Rating: (9/100% )	I am just about to start moving so i wont have any of that kind of info handy. Maybe in a bout a week i can help you out. Why do you want to goto 9 anyway? How much PSI you looking to pump into the motor?

04-25-2009, 01:23 PM	#10 (permalink)
Oteck RAAAGE! Join Date: Aug 2005 Posts: 2,110 Thanks: 8 Thanked 60 Times in 57 Posts Blog Entries: 2 iTrader Rating: (3/100% )	save one .90" Hi-flow valves for me next weekend, will be in the shop or your out of town?

04-26-2009, 07:05 AM	#11 (permalink)
johnny g Talentless Researcher Join Date: Sep 2006 Location: Liverpool, England. Posts: 278 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	Johnny, what have you got left for the 3VZ and the 1MZ? What prices?

05-08-2009, 03:21 AM	#13 (permalink)
thwam Cage Fighter Join Date: May 2005 Posts: 294 Thanks: 0 Thanked 7 Times in 7 Posts iTrader Rating: (0/0% )	Weasy, do you still have 5VZ pistons available? Thanks! Todd

05-09-2009, 11:26 PM	#15 (permalink)
Weasy2k 3.4L 10K RPM In the works Join Date: Mar 2005 Location: Vancouver, BC Posts: 8,895 Thanks: 34 Thanked 80 Times in 66 Posts iTrader Rating: (9/100% )	Hey everyone. Sorry about delays in response, i am in the middle of moving and the cable company are taking thier sweet arse time making the switch. Should be back online just after the 15th.

05-14-2009, 08:14 PM	#16 (permalink)
U-235 E=mr2 Join Date: Jun 2007 Location: In the back, where no one sees me. Posts: 302 Thanks: 13 Thanked 4 Times in 4 Posts iTrader Rating: (12/100% )	Hey Johnny I had a quick question about the valves. My mechanically inclined friend said that sometimes valves need to be machined to fit in the appropriate head. The 5vz standard length valves are just plug-n-play, right? No additional work required? Thanks so much for all your help!

05-17-2009, 02:48 PM	#17 (permalink)
Weasy2k 3.4L 10K RPM In the works Join Date: Mar 2005 Location: Vancouver, BC Posts: 8,895 Thanks: 34 Thanked 80 Times in 66 Posts iTrader Rating: (9/100% )	tHE only thing you would need to do is make sure the valve clearance to the cams is ok. Standard procedure, but no big machining needed at all.

05-27-2009, 12:07 PM	#18 (permalink)
sav234 No Skills Join Date: May 2009 Posts: 4 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	Hey mate do you have any rods and pistons for the 1mz? Im looking to buy 2 sets and if possible some valves and springs.

07-02-2009, 06:33 AM	#19 (permalink)
johnny g Talentless Researcher Join Date: Sep 2006 Location: Liverpool, England. Posts: 278 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	Any update on our conversations mate?

07-09-2009, 02:39 AM	#20 (permalink)
5vzbound No Skills Join Date: Feb 2008 Posts: 35 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (1/100% )	are the vavles and springs gone for good? if so where can i track them down. I have the pistons, now its time for valves springs and cams