AEM Wiring??

rcohen · 02-01-2007, 05:02 PM

Where can I find wiring information for installing my AEM EMS with the GM AIT, GM 3 bar MAP and GM boost solenoid? Also I am trying to wire my MSD 6a, Tach adapter and Blaster coil. Where do I start. Is there somewhere that I can find this wiring info?? Any help is very much appreciated..

Thanks in advance

Enthalpy · 02-02-2007, 03:56 PM

FYI - The MSD stuff isn't necessary until you are making fairly mad power. As for the IAT, 3 bar MAP sensor and boost solenoid:

Boost solenoid gets wired to A6. Assign it to PW2. As for the IAT sensor, you can use the wires going to the stock AFM's THA and E2 pins. Use the stock MAP sensor's wiring for the GM MAP sensor. The wiring is VC for VCC+ power, E2 for sensor ground and PIM for the ECU signal wire. That all should be there in the stock MAP sensor's plug.

If you want a completely PnP setup, I can get you the part numbers for the pins with pigtails so you can wire it straight into the EMS. This way, you can simply pull these pins out of the stock harness and reuse them if you intend on putting the stock ECU back in for any reason (like emissions testing).

Don't forget to rescale your fuel map based on the new MAP sensor.

MR2TuRbZ · 02-02-2007, 04:26 PM

hmm, i didnt know that you could get the pins from toyota... do you have the P/N?

Enthalpy · 02-02-2007, 04:47 PM

I would have to dig it up. It would take me some time, but I do have all the pin part numbers.

rcohen · 02-02-2007, 11:19 PM

Damn, man... Thats awsome info. I appreciate it. Thank You!!!!!!!!!

Enthalpy · 02-03-2007, 01:15 AM

Sure! Any time!

MR2TuRbZ · 02-03-2007, 01:47 AM

kick ass! thanks

02-01-2007, 05:02 PM	#1 (permalink)
rcohen No Skills Join Date: Jan 2006 Posts: 117 Thanks: 2 Thanked 1 Time in 1 Post iTrader Rating: (2/100% )	AEM Wiring?? Where can I find wiring information for installing my AEM EMS with the GM AIT, GM 3 bar MAP and GM boost solenoid? Also I am trying to wire my MSD 6a, Tach adapter and Blaster coil. Where do I start. Is there somewhere that I can find this wiring info?? Any help is very much appreciated.. Thanks in advance

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-02-2007, 03:56 PM	#2 (permalink)
Enthalpy EMS Harmonizer Join Date: Feb 2006 Location: Denver, CO Posts: 1,219 Thanks: 8 Thanked 54 Times in 42 Posts My Google Map iTrader Rating: (2/100% )	FYI - The MSD stuff isn't necessary until you are making fairly mad power. As for the IAT, 3 bar MAP sensor and boost solenoid: Boost solenoid gets wired to A6. Assign it to PW2. As for the IAT sensor, you can use the wires going to the stock AFM's THA and E2 pins. Use the stock MAP sensor's wiring for the GM MAP sensor. The wiring is VC for VCC+ power, E2 for sensor ground and PIM for the ECU signal wire. That all should be there in the stock MAP sensor's plug. If you want a completely PnP setup, I can get you the part numbers for the pins with pigtails so you can wire it straight into the EMS. This way, you can simply pull these pins out of the stock harness and reuse them if you intend on putting the stock ECU back in for any reason (like emissions testing). Don't forget to rescale your fuel map based on the new MAP sensor.

02-02-2007, 04:26 PM	#3 (permalink)
MR2TuRbZ Local V8 Killer Join Date: Jun 2005 Location: Indianapolis Posts: 556 Thanks: 8 Thanked 7 Times in 7 Posts My Google Map iTrader Rating: (2/100% )	hmm, i didnt know that you could get the pins from toyota... do you have the P/N?

02-02-2007, 04:47 PM	#4 (permalink)
Enthalpy EMS Harmonizer Join Date: Feb 2006 Location: Denver, CO Posts: 1,219 Thanks: 8 Thanked 54 Times in 42 Posts My Google Map iTrader Rating: (2/100% )	I would have to dig it up. It would take me some time, but I do have all the pin part numbers.

02-02-2007, 11:19 PM	#5 (permalink)
rcohen No Skills Join Date: Jan 2006 Posts: 117 Thanks: 2 Thanked 1 Time in 1 Post iTrader Rating: (2/100% )	Damn, man... Thats awsome info. I appreciate it. Thank You!!!!!!!!!

02-03-2007, 01:15 AM	#6 (permalink)
Enthalpy EMS Harmonizer Join Date: Feb 2006 Location: Denver, CO Posts: 1,219 Thanks: 8 Thanked 54 Times in 42 Posts My Google Map iTrader Rating: (2/100% )	Sure! Any time!

02-03-2007, 01:47 AM	#7 (permalink)
MR2TuRbZ Local V8 Killer Join Date: Jun 2005 Location: Indianapolis Posts: 556 Thanks: 8 Thanked 7 Times in 7 Posts My Google Map iTrader Rating: (2/100% )	kick ass! thanks