3S-GTE USDM Turbo Engine Downpipes - Page 5

PVpower · 08-22-2009, 09:59 PM

I posted earlier that I was happy with my dp however now I think It may be causing my wastegate to stay open. Doing some checks to be sure. I saw something about grinding the eBay dps what all needs grinded down to make sure the wg doesn't stick?

2onaem · 12-22-2009, 08:52 PM

ats 20g kit dp with re-routed wastgate... fitment sucks!!! hits the firewall the wastegate doesnt sit properly flush... next time im going with ko racing!

Xceler8 · 03-12-2010, 03:00 PM

I just installed the Berk Technology pipe with the high heat coating. Fit is tight but it clears everything, that being said, it optimizes the space that is available to have the largest radius bends and the largest bellmouth possible.

It clears the stock heat shield (although you can trim it for more clearance) as well as the firewall heat sheilds. The only place that it is tighter than I like is near the AC lines; and note that the AC compressor needs to be temporarily unbolted to attack the downpipe. I plan on fixing the problem by wrapping the AC line in a reflective tape to cut down on the radiated heat.

Also I think the picture on the first page needs to be updated for this guy, it comes with a flex section and a support bracket as well which is nice.

mac51o · 06-07-2010, 12:48 AM

my cars running too rich, i have a ko downpipe, will putting back the oem downpipe back (cause of the cat) on there help make it less rich?

btw i have have any other mods besides the apexi intake

tlesiak91 · 10-13-2010, 12:59 PM

Quote:

Originally Posted by PHOENIX

GreddySetGo custom
Stainless Steel 3" downpipes!!! - Toyota MR2 Message Board

http://www.mr2.com/files/Forum Stick...ductreview.jpg

-321 Stainless Steel
-Support bracket included
-Extra O2 sensor port
-EGT port (or Gen3 OEM cat temp sensor)
-Gaskets included
-3" to 2.5" exhaust adapter and gasket also included
-All necessary hardware (studs, bolts) included

http://www.mr2.com/files/Forum Stick...reddysetgo.jpg

ATS TD06 DP
ATS Racing TD06 Replacement Downpipe

http://www.mr2.com/files/Forum Stick...ductreview.jpg

- replaces cracked or broken greedy tdo6 dp
- no other information available

http://www.mr2.com/files/Forum Stick...es/atstd06.jpg

Works Power
http://www.workspower.net/downpipe.html

http://www.mr2.com/files/Forum Stick...ductreview.jpg

- Tig welded
- 321 stainless steel
- 2.5 expanding to 3 inch diameter

http://www.mr2.com/files/Forum Stick...workspower.gif

Extreme Boost
eXtremeBoost.com

http://www.mr2.com/files/Forum Stick...ductreview.jpg

- 304 stainless steet
- polished
- 3 inch diameter

http://www.mr2.com/files/Forum Stick...tremeboost.jpg

Blitz
turbo kit blitz performance supercharger at blitz-performance.com

http://www.mr2.com/files/Forum Stick...ductreview.jpg

- cast construction
- for ct26 and ct20b applications

http://www.mr2.com/files/Forum Stick...ipes/blitz.jpg

Ebay Specials
mr2 downpipe, great deals on eBay Motors on eBay!

http://www.mr2.com/files/Forum Stick...ductreview.jpg

- there are a couple different no name types on eBay with not enough information to really make its own section for them. No one really knows much about these yet although I am sure we will here about them soon in the product review area. Till then, im not gonna say anything about them since they seem to come and go every other week.

http://www.mr2.com/files/Forum Stick...ipes/ebay1.jpg
http://www.mr2.com/files/Forum Stick...ipes/ebay2.jpg

im only putting a few bolt ons and i think im gonna try the ebay downpipe for now

jstn116 · 11-17-2010, 08:35 AM

quick nubie question... do these pipes produce more horsepower and if so about how much...."hence about how much"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

LinkBacks (?) LinkBack to this Thread: http://www.mr2.com/forums/turbo-engine-talk-modifications-swaps/Toyota-MR2-2766-downpipes.html
Posted By	For	Type	Date
alltrac.net gtfour.net • View topic - Interest Thread: Berk Technology 3	This thread	Refback	05-16-2010 01:30 PM
alltrac.net gtfour.net • View topic - Interest Thread: Berk Technology 3	This thread	Refback	01-06-2010 11:39 AM
alltrac.net gtfour.net • View topic - Interest Thread: Berk Technology 3" Midpipe	This thread	Refback	12-22-2009 02:41 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3" Midpipe	This thread	Refback	11-23-2009 01:36 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	10-28-2009 11:46 AM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	07-08-2009 02:58 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	03-26-2009 05:34 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	04-30-2008 01:09 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	12-15-2007 07:43 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	12-15-2007 01:56 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	12-15-2007 01:21 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	12-15-2007 12:17 PM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	12-15-2007 10:55 AM
alltrac.net :: View topic - Interest Thread: Berk Technology 3	This thread	Refback	12-15-2007 04:50 AM
Toyota MR2 Message Board	This thread	Refback	09-17-2007 09:24 PM

08-22-2009, 09:59 PM	#81 (permalink)
PVpower Cage Fighter Join Date: Feb 2008 Posts: 359 Thanks: 1 Thanked 2 Times in 2 Posts My Google Map iTrader Rating: (2/100% )	I posted earlier that I was happy with my dp however now I think It may be causing my wastegate to stay open. Doing some checks to be sure. I saw something about grinding the eBay dps what all needs grinded down to make sure the wg doesn't stick?

12-22-2009, 08:52 PM	#82 (permalink)
2onaem is that thing really FAST Join Date: Aug 2008 Location: raleigh Posts: 153 Thanks: 1 Thanked 5 Times in 5 Posts iTrader Rating: (2/100% )	ats 20g kit dp with re-routed wastgate... fitment sucks!!! hits the firewall the wastegate doesnt sit properly flush... next time im going with ko racing!

03-12-2010, 03:00 PM	#83 (permalink)
Xceler8 Newly Boosted Join Date: Aug 2005 Location: Gainesville Posts: 113 Thanks: 0 Thanked 1 Time in 1 Post My Google Map iTrader Rating: (1/100% )	I just installed the Berk Technology pipe with the high heat coating. Fit is tight but it clears everything, that being said, it optimizes the space that is available to have the largest radius bends and the largest bellmouth possible. It clears the stock heat shield (although you can trim it for more clearance) as well as the firewall heat sheilds. The only place that it is tighter than I like is near the AC lines; and note that the AC compressor needs to be temporarily unbolted to attack the downpipe. I plan on fixing the problem by wrapping the AC line in a reflective tape to cut down on the radiated heat. Also I think the picture on the first page needs to be updated for this guy, it comes with a flex section and a support bracket as well which is nice.

06-07-2010, 12:48 AM	#84 (permalink)
mac51o No Skills Join Date: May 2010 Location: bay area Posts: 18 Thanks: 0 Thanked 1 Time in 1 Post iTrader Rating: (0/0% )	my cars running too rich, i have a ko downpipe, will putting back the oem downpipe back (cause of the cat) on there help make it less rich? btw i have have any other mods besides the apexi intake

11-17-2010, 08:35 AM	#86 (permalink)
jstn116 No Skills Join Date: Sep 2010 Posts: 33 Thanks: 0 Thanked 0 Times in 0 Posts iTrader Rating: (0/0% )	quick nubie question... do these pipes produce more horsepower and if so about how much...."hence about how much"